lkml.org 
[lkml]   [2018]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC v1 3/7] clk: meson: clk-pll: check if the clock is already enabled
From
Date
On Wed, 2018-11-14 at 23:57 +0100, Martin Blumenstingl wrote:
> Since commit 6f888e7bc7bd58 ("clk: meson: clk-pll: add enable bit") our
> PLLs also support the "enable" bit. Currently meson_clk_pll_enable
> unconditionally resets the PLL, enables it, takes it out of reset and
> waits until it is locked.
>
> This works fine for our current clock trees. However, there will be a
> problem once we allow modifications to sys_pll on Meson8, Meson8b and
> Meson8m2 (which will be required for CPU frequency scaling):
> the CPU clock is derived from the sys_pll clock. Once clk_enable is
> called on the CPU clock this will be propagated by the common clock
> framework up until the sys_pll clock. If we reset the PLL
> unconditionally in meson_clk_pll_enable the CPU will be stopped (on
> Meson8, Meson8b and Meson8m2).
> To prevent this we simply check if the PLL is already enabled and do
> reset the PLL if it's already enabled and locked.
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> ---
> drivers/clk/meson/clk-pll.c | 21 +++++++++++++++++++++
> 1 file changed, 21 insertions(+)
>
> diff --git a/drivers/clk/meson/clk-pll.c b/drivers/clk/meson/clk-pll.c
> index f5b5b3fabe3c..b46cca953f4f 100644
> --- a/drivers/clk/meson/clk-pll.c
> +++ b/drivers/clk/meson/clk-pll.c
> @@ -200,11 +200,32 @@ static void meson_clk_pll_init(struct clk_hw *hw)
> }
> }
>
> +static int meson_clk_pll_is_enabled(struct clk_hw *hw)
> +{
> + struct clk_regmap *clk = to_clk_regmap(hw);
> + struct meson_clk_pll_data *pll = meson_clk_pll_data(clk);
> +
> + if (meson_parm_read(clk->map, &pll->rst))
> + return 0;
> +
> + if (!meson_parm_read(clk->map, &pll->en))
> + return 0;
> +
> + if (!meson_parm_read(clk->map, &pll->l))
> + return 0;

Could you use an OR instead of these 3 seperate checks ?

> +
> + return 1;
> +}
> +
> static int meson_clk_pll_enable(struct clk_hw *hw)
> {
> struct clk_regmap *clk = to_clk_regmap(hw);
> struct meson_clk_pll_data *pll = meson_clk_pll_data(clk);
>
> + /* do nothing if the PLL is already enabled */
> + if (meson_clk_pll_is_enabled(hw))
> + return 0;
> +
> /* Make sure the pll is in reset */
> meson_parm_write(clk->map, &pll->rst, 1);
>
>

With the small comment above taken care of, it makes perfect sense
and it will be valuable to other PLLs, Thx Martin !

Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>


\
 
 \ /
  Last update: 2018-11-15 10:15    [W:0.115 / U:4.840 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site