lkml.org 
[lkml]   [2018]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/2] clocksource: meson6_timer: use register names from the datasheet
Hi Daniel,

thanks for your feedback!

On Thu, Nov 15, 2018 at 2:35 AM Daniel Lezcano
<daniel.lezcano@linaro.org> wrote:
>
> On 28/10/2018 13:55, Martin Blumenstingl wrote:
> > This makes the driver use the names from S805 datasheet for the
> > preprocessor #defines. This makes it easier to spot that the driver
> > currently only supports Timer A (as clockevent with interrupt support)
> > and Timer E (as clocksource without interrupts). Timer B, C and D (which
> > are similar to Timer A) are currently not supported by the driver.
> >
> > While here, this also removes the internal "CED_ID" and "CSD_ID" defines
> > which are used to identify the timer. These IDs are not described in the
> > datasheet and thus make it harder to compare the code to what's written
> > in the datasheet.
> >
> > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> > ---
> > drivers/clocksource/meson6_timer.c | 110 ++++++++++++++++++-----------
> > 1 file changed, 68 insertions(+), 42 deletions(-)
> >
> > diff --git a/drivers/clocksource/meson6_timer.c b/drivers/clocksource/meson6_timer.c
> > index 92f20991a937..c622135bee9d 100644
> > --- a/drivers/clocksource/meson6_timer.c
> > +++ b/drivers/clocksource/meson6_timer.c
> > @@ -10,6 +10,8 @@
> > * warranty of any kind, whether express or implied.
> > */
> >
> > +#include <linux/bitfield.h>
> > +#include <linux/bitops.h>
> > #include <linux/clk.h>
> > #include <linux/clockchips.h>
> > #include <linux/interrupt.h>
> > @@ -20,80 +22,102 @@
> > #include <linux/of_address.h>
> > #include <linux/of_irq.h>
> >
> > -#define CED_ID 0
> > -#define CSD_ID 4
> > -
> > -#define TIMER_ISA_MUX 0
> > -#define TIMER_ISA_VAL(t) (((t) + 1) << 2)
> > -
> > -#define TIMER_INPUT_BIT(t) (2 * (t))
> > -#define TIMER_ENABLE_BIT(t) (16 + (t))
> > -#define TIMER_PERIODIC_BIT(t) (12 + (t))
> > +enum meson6_timera_input_clock {
> > + MESON_TIMERA_CLOCK_1US = 0x0,
> > + MESON_TIMERA_CLOCK_10US = 0x1,
> > + MESON_TIMERA_CLOCK_100US = 0x2,
> > + MESON_TIMERA_CLOCK_1MS = 0x3,
> > +};
> >
> > -#define TIMER_CED_INPUT_MASK (3UL << TIMER_INPUT_BIT(CED_ID))
> > -#define TIMER_CSD_INPUT_MASK (7UL << TIMER_INPUT_BIT(CSD_ID))
> > +enum meson6_timere_input_clock {
> > + MESON_TIMERE_CLOCK_SYSTEM_CLOCK = 0x0,
> > + MESON_TIMERE_CLOCK_1US = 0x1,
> > + MESON_TIMERE_CLOCK_10US = 0x2,
> > + MESON_TIMERE_CLOCK_100US = 0x3,
> > + MESON_TIMERE_CLOCK_1MS = 0x4,
> > +};
>
> It is not required to specify the values. The standard defines the
> default first value is zero, and each enum has the value which is +1 of
> the previous one.
the idea behind this is: these are values from the datasheet so I
wanted to make them easy to find when comparing the datasheet with the
driver.
I will replace the enums with simple #defines if there are no
objections (that also makes it consistent with the other register
values in the driver).


Regards
Martin

\
 
 \ /
  Last update: 2018-11-15 07:23    [W:0.056 / U:4.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site