lkml.org 
[lkml]   [2018]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
SubjectRE: [PATCH net-next v3 6/6] net/ncsi: Configure multi-package, multi-channel modes with failover
Date
Hi Samuel,

After running more testing, I notice that the extra patch causing failover function
to fail. Also, occasionally, I will see two channels having TX enabled if I
send netlink command back-to-back.

cat /sys/kernel/debug/ncsi_protocol/ncsi_device_
IFIDX IFNAME NAME PID CID RX TX MP MC WP WC PC CS PS LS RU CR NQ HA
=====================================================================
2 eth2 ncsi0 000 000 1 1 1 1 1 1 1 2 1 1 1 1 0 1
2 eth2 ncsi1 000 001 1 1 1 1 1 1 0 2 1 1 1 1 0 1
2 eth2 ncsi2 001 000 0 0 1 1 0 0 0 1 0 1 1 1 0 1
2 eth2 ncsi3 001 001 0 0 1 1 0 0 0 1 0 1 1 1 0 1
=====================================================================
MP: Multi-mode Package WP: Whitelist Package
MC: Multi-mode Channel WC: Whitelist Channel
PC: Primary Channel CS: Channel State IA/A/IV 1/2/3
PS: Poll Status LS: Link Status
RU: Running CR: Carrier OK
NQ: Queue Stopped HA: Hardware Arbitration

Thanks,
Justin


> From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
> From: Samuel Mendoza-Jonas <sam@mendozajonas.com>
> Date: Fri, 9 Nov 2018 13:11:03 +1100
> Subject: [PATCH] net/ncsi: Reset state fixes, single-channel LSC
>
> ---
> net/ncsi/ncsi-aen.c | 8 +++++---
> net/ncsi/ncsi-manage.c | 19 +++++++++++++++----
> 2 files changed, 20 insertions(+), 7 deletions(-)
>
> diff --git a/net/ncsi/ncsi-aen.c b/net/ncsi/ncsi-aen.c
> index 39c2e9eea2ba..034cb1dc5566 100644
> --- a/net/ncsi/ncsi-aen.c
> +++ b/net/ncsi/ncsi-aen.c
> @@ -93,14 +93,16 @@ static int ncsi_aen_handler_lsc(struct ncsi_dev_priv *ndp,
> if ((had_link == has_link) || chained)
> return 0;
>
> - if (!ndp->multi_package && !nc->package->multi_channel) {
> - if (had_link)
> - ndp->flags |= NCSI_DEV_RESHUFFLE;
> + if (!ndp->multi_package && !nc->package->multi_channel && had_link) {
> + ndp->flags |= NCSI_DEV_RESHUFFLE;
> ncsi_stop_channel_monitor(nc);
> spin_lock_irqsave(&ndp->lock, flags);
> list_add_tail_rcu(&nc->link, &ndp->channel_queue);
> spin_unlock_irqrestore(&ndp->lock, flags);
> return ncsi_process_next_channel(ndp);
> + } else {
> + /* Configured channel came up */
> + return 0;

It is always going to else statement if multi_package and/or mutlit_channel is enabled.

npcm7xx-emc f0825000.eth eth2: NCSI: ncsi_aen_handler_lsc() - pkg 0 ch 0 state down
npcm7xx-emc f0825000.eth eth2: NCSI: ncsi_aen_handler_lsc() - had_link 1, has_link 0, chained 0

These codes have no chance to run.
if (had_link) {
ncm = &nc->modes[NCSI_MODE_TX_ENABLE];
if (ncsi_channel_is_last(ndp, nc)) {
/* No channels left, reconfigure */
return ncsi_reset_dev(&ndp->ndev);
} else if (ncm->enable) {
/* Need to failover Tx channel */
ncsi_update_tx_channel(ndp, nc->package, nc, NULL);
}

> }
>
\
 
 \ /
  Last update: 2018-11-09 22:59    [W:0.162 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site