lkml.org 
[lkml]   [2018]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V6 16/23] mmc: mmci: add variant property to write datactrl before command
Date
From: Ludovic Barre <ludovic.barre@st.com>

This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.

Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
---
drivers/mmc/host/mmci.c | 6 ++++--
drivers/mmc/host/mmci.h | 2 ++
2 files changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index ca442fb..66aa59f 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -1267,7 +1267,8 @@ mmci_cmd_irq(struct mmci_host *host, struct mmc_command *cmd,
mmci_request_end(host, host->mrq);
} else if (sbc) {
mmci_start_command(host, host->mrq->cmd, 0);
- } else if (!(cmd->data->flags & MMC_DATA_READ)) {
+ } else if (!host->variant->datactrl_first &&
+ !(cmd->data->flags & MMC_DATA_READ)) {
mmci_start_data(host, cmd->data);
}
}
@@ -1531,7 +1532,8 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
if (mrq->data)
mmci_get_next_data(host, mrq->data);

- if (mrq->data && mrq->data->flags & MMC_DATA_READ)
+ if (mrq->data &&
+ (host->variant->datactrl_first || mrq->data->flags & MMC_DATA_READ))
mmci_start_data(host, mrq->data);

if (mrq->sbc)
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 783a7ad..eef7dd5 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -223,6 +223,7 @@ struct mmci_host;
* @datactrl_mask_sdio: SDIO enable mask in datactrl register
* @datactrl_blksz: block size in power of two
* @datactrl_dpsm_enable: enable value for DPSM
+ * @datactrl_first: true if data must be setup before send command
* @pwrreg_powerup: power up value for MMCIPOWER register
* @f_max: maximum clk frequency supported by the controller.
* @signal_direction: input/out direction of bus signals can be indicated
@@ -262,6 +263,7 @@ struct variant_data {
unsigned int datactrl_mask_sdio;
unsigned int datactrl_blocksz;
unsigned int datactrl_dpsm_enable;
+ u8 datactrl_first:1;
u8 st_sdio:1;
u8 st_clkdiv:1;
u8 blksz_datactrl16:1;
--
2.7.4
\
 
 \ /
  Last update: 2018-10-08 14:12    [W:0.136 / U:3.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site