lkml.org 
[lkml]   [2018]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 1/2] spi: Add MXIC controller driver
Hi Mason,

On Mon, 8 Oct 2018 10:25:31 +0800
masonccyang@mxic.com.tw wrote:

> +static int mxic_spi_clk_enable(struct mxic_spi *mxic)
> +{
> + int ret;
> +
> + ret = clk_prepare_enable(mxic->send_clk);
> + if (ret)
> + goto out;

Please don't use gotos when it's not necessary, just do

return ret;

> +
> + ret = clk_prepare_enable(mxic->send_dly_clk);
> + if (ret)
> + goto err_send_dly_clk;
> +
> + return ret;
> +
> +err_send_dly_clk:
> + clk_disable_unprepare(mxic->send_clk);
> +out:

and you can get rid of the out label.

> + return ret;
> +}
> +


> +static int mxic_spi_mem_exec_op(struct spi_mem *mem,
> + const struct spi_mem_op *op)
> +{
> + struct spi_master *master = spi_master_get(mem->spi->master);
> + struct mxic_spi *mxic = spi_master_get_devdata(mem->spi->master);
> + int nio = 1, i, ret;
> + u32 ss_ctrl;
> + u8 addr[8];
> +
> + if (master->prepare_transfer_hardware)
> + master->prepare_transfer_hardware(master);

Move the mxic_prepare_transfer_hardware() at the top of the file and
call it directly from there.

> +
> + if (mem->spi->mode & (SPI_TX_QUAD | SPI_RX_QUAD))
> + nio = 4;
> + else if (mem->spi->mode & (SPI_TX_DUAL | SPI_RX_DUAL))
> + nio = 2;
> +
> + writel(HC_CFG_NIO(nio) |
> + HC_CFG_TYPE(mem->spi->chip_select, HC_CFG_TYPE_SPI_NOR) |
> + HC_CFG_SLV_ACT(mem->spi->chip_select) | HC_CFG_IDLE_SIO_LVL(1) |
> + HC_CFG_MAN_CS_EN,
> + mxic->regs + HC_CFG);
> + writel(HC_EN_BIT, mxic->regs + HC_EN);
> +
> + ss_ctrl = OP_CMD_BYTES(1) | OP_CMD_BUSW(fls(op->cmd.buswidth) - 1);
> +
> + if (op->addr.nbytes)
> + ss_ctrl |= OP_ADDR_BYTES(op->addr.nbytes) |
> + OP_ADDR_BUSW(fls(op->addr.buswidth) - 1);
> +
> + if (op->dummy.nbytes)
> + ss_ctrl |= OP_DUMMY_CYC(op->dummy.nbytes);
> +
> + if (op->data.nbytes) {
> + ss_ctrl |= OP_DATA_BUSW(fls(op->data.buswidth) - 1);
> + if (op->data.dir == SPI_MEM_DATA_IN)
> + ss_ctrl |= OP_READ;
> + }
> +
> + writel(ss_ctrl, mxic->regs + SS_CTRL(mem->spi->chip_select));
> +
> + writel(readl(mxic->regs + HC_CFG) | HC_CFG_MAN_CS_ASSERT,
> + mxic->regs + HC_CFG);
> +
> + ret = mxic_spi_data_xfer(mxic, &op->cmd.opcode, NULL, 1);
> + if (ret)
> + goto out;
> +
> + for (i = 0; i < op->addr.nbytes; i++)
> + addr[i] = op->addr.val >> (8 * (op->addr.nbytes - i - 1));
> +
> + ret = mxic_spi_data_xfer(mxic, addr, NULL, op->addr.nbytes);
> + if (ret)
> + goto out;
> +
> + ret = mxic_spi_data_xfer(mxic, NULL, NULL, op->dummy.nbytes);
> + if (ret)
> + goto out;
> +
> + ret = mxic_spi_data_xfer(mxic,
> + op->data.dir == SPI_MEM_DATA_OUT ?
> + op->data.buf.out : NULL,
> + op->data.dir == SPI_MEM_DATA_IN ?
> + op->data.buf.in : NULL,
> + op->data.nbytes);
> +
> +out:
> + writel(readl(mxic->regs + HC_CFG) & ~HC_CFG_MAN_CS_ASSERT,
> + mxic->regs + HC_CFG);
> + writel(0, mxic->regs + HC_EN);
> +
> + return ret;
> +}

[...]

> +
> +static int mxic_spi_setup(struct spi_device *spi)
> +{
> + struct mxic_spi *mxic = spi_master_get_devdata(spi->master);
> +
> + mxic->cur_speed_hz = spi->max_speed_hz;

This is wrong, ->cur_speed_hz should be updated in
mxic_prepare_transfer_hardware() or mxic_spi_clk_check(), not when
->setup() is called. Also, you seem to ignore the xfer->speed_hz value,
which might be different from spi->max_speed_hz. Maybe the
->prepare_transfer() hook is not the right place to do this
->cur_speed_hz selection in the end.

Can you instead create the following function:

static int mxic_spi_set_freq(struct mxic_spi *mxic, unsigned long freq)
{
if (mxic->cur_speed_hz == freq)
return 0;

mxic_spi_clk_disable(mxic);
ret = mxic_spi_clk_setup(mxic, master->max_speed_hz);
if (ret)
return ret;

ret = mxic_spi_clk_enable(mxic);
if (ret)
return ret;

mxic->cur_speed_hz = freq;
return 0;
}

and then call it from mxic_spi_transfer_one() and
mxic_spi_mem_exec_op():

static int mxic_spi_mem_exec_op(struct spi_mem *mem,
const struct spi_mem_op *op)
{
...
ret = mxic_spi_set_freq(mxic, mem->spi->max_speed_hz);
...
}

static int mxic_spi_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *t)
{
...
ret = mxic_spi_set_freq(mxic, t->speed_hz);
...
}

> +
> + return 0;
> +}
> +

[...]

> +
> +static int mxic_unprepare_transfer_hardware(struct spi_master *master)
> +{
> + return 0;
> +}

If the function does nothing, just leave ->unprepare_transfer to NULL.


> +
> +static int mxic_spi_remove(struct platform_device *pdev)
> +{
> + struct spi_master *master = platform_get_drvdata(pdev);
> + struct mxic_spi *mxic = spi_master_get_devdata(master);
> +
> + mxic_spi_clk_disable(mxic);
> + clk_disable_unprepare(mxic->ps_clk);
> + pm_runtime_disable(&pdev->dev);

Are you sure you still have to call mxic_spi_clk_disable() and
clk_disable_unprepare() here? Shouldn't it be handled when you call
pm_runtime_disable()?

> +
> + spi_unregister_master(master);
> +
> + return 0;
> +}
> +

Regards,

Boris

\
 
 \ /
  Last update: 2018-10-08 10:39    [W:0.024 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site