lkml.org 
[lkml]   [2018]   [Oct]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] seco-cec: add Consumer-IR support
Hi Sean,

On Thu, Oct 04, 2018 at 02:49:27PM +0100, Sean Young wrote:
> On Tue, Oct 02, 2018 at 06:59:56PM +0200, ektor5 wrote:
> > From: Ettore Chimenti <ek5.chimenti@gmail.com>
> >
> > Introduce support for Consumer-IR into seco-cec driver, as it shares the
> > same interrupt for receiving messages.
> > The device decodes RC5 signals only, defaults to hauppauge mapping.
> > It will spawn an input interface using the RC framework (like CEC
> > device).
> >
> > Signed-off-by: Ettore Chimenti <ek5.chimenti@gmail.com>
> > ---
> > drivers/media/platform/Kconfig | 10 ++
> > drivers/media/platform/seco-cec/seco-cec.c | 136 ++++++++++++++++++++-
> > drivers/media/platform/seco-cec/seco-cec.h | 11 ++
> > 3 files changed, 154 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig
> > index f477764b902a..5833f488eef8 100644
> > --- a/drivers/media/platform/Kconfig
> > +++ b/drivers/media/platform/Kconfig
> > @@ -624,6 +624,16 @@ config VIDEO_SECO_CEC
> > CEC bus is present in the HDMI connector and enables communication
> > between compatible devices.
> >
> > +config VIDEO_SECO_RC
> > + bool "SECO Boards IR RC5 support"
> > + depends on VIDEO_SECO_CEC
> > + select RC_CORE
> > + help
> > + If you say yes here you will get support for the
> > + SECO Boards Consumer-IR in seco-cec driver.
> > + The embedded controller supports RC5 protocol only, default mapping
> > + is set to rc-hauppauge.
>
> Strange mixture of spaces/tabs.

Ops. Yes, will fix.

>
> > +
> > endif #CEC_PLATFORM_DRIVERS
> >
> > menuconfig SDR_PLATFORM_DRIVERS
> > diff --git a/drivers/media/platform/seco-cec/seco-cec.c b/drivers/media/platform/seco-cec/seco-cec.c
> > index ba3b7c144a87..ee1949395cf4 100644
> > --- a/drivers/media/platform/seco-cec/seco-cec.c
> > +++ b/drivers/media/platform/seco-cec/seco-cec.c
> > @@ -28,6 +28,9 @@ struct secocec_data {
> > struct platform_device *pdev;
> > struct cec_adapter *cec_adap;
> > struct cec_notifier *notifier;
> > + struct rc_dev *irda_rc;
> > + char irda_input_name[32];
> > + char irda_input_phys[32];
>
> IrDA is a completely different encoding than RC-5, CIR or anything rc-core
> supports; RC-5 is much lower transmission speed. Please do not conflate
> the two, and rename it either ir_input_phys or rc_input_phys (same for the
> rest of the functions/members in the rest of the file).

Yes, I figured out that in the middle of developing. I got rid of most
of the "irda" references, but I have accidentally left some of them.
Will finish the work.

>
> > int irq;
> > };
> >
> > @@ -383,6 +386,119 @@ struct cec_adap_ops secocec_cec_adap_ops = {
> > .adap_transmit = secocec_adap_transmit,
> > };
> >
> > +#ifdef CONFIG_VIDEO_SECO_RC
> > +static int secocec_irda_probe(void *priv)
> > +{
> > + struct secocec_data *cec = priv;
> > + struct device *dev = cec->dev;
> > + int status;
> > + u16 val;
> > +
> > + /* Prepare the RC input device */
> > + cec->irda_rc = devm_rc_allocate_device(dev, RC_DRIVER_SCANCODE);
> > + if (!cec->irda_rc) {
> > + dev_err(dev, "Failed to allocate memory for rc_dev");
>
> No need to dev_err() here, kmalloc() will have already reported the error.

Ok, will remove.

>
> > + return -ENOMEM;
> > + }
> > +
> > + snprintf(cec->irda_input_name, sizeof(cec->irda_input_name),
> > + "IrDA RC for %s", dev_name(dev));
>
> Since it's an RC device there is no need to put RC in the name. Just
> use dev_name() as the device_name.

I took that from CEC RC Passthrough device name.

>
> > + snprintf(cec->irda_input_phys, sizeof(cec->irda_input_phys),
> > + "%s/input0", dev_name(dev));
> > +
> > + cec->irda_rc->device_name = cec->irda_input_name;
> > + cec->irda_rc->input_phys = cec->irda_input_phys;
> > + cec->irda_rc->input_id.bustype = BUS_HOST;
> > + cec->irda_rc->input_id.vendor = 0;
> > + cec->irda_rc->input_id.product = 0;
> > + cec->irda_rc->input_id.version = 1;
> > + cec->irda_rc->driver_name = SECOCEC_DEV_NAME;
> > + cec->irda_rc->allowed_protocols = RC_PROTO_BIT_RC5;
> > + cec->irda_rc->enabled_protocols = RC_PROTO_BIT_RC5;
>
> No need to set enabled_protocols.

Ok.

>
> > + cec->irda_rc->priv = cec;
> > + cec->irda_rc->map_name = RC_MAP_HAUPPAUGE;
> > + cec->irda_rc->timeout = MS_TO_NS(100);
> > +
> > + /* Clear the status register */
> > + status = smb_rd16(SECOCEC_STATUS_REG_1, &val);
> > + if (status != 0)
> > + goto err;
> > +
> > + status = smb_wr16(SECOCEC_STATUS_REG_1, val);
> > + if (status != 0)
> > + goto err;
> > +
> > + /* Enable the interrupts */
> > + status = smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> > + if (status != 0)
> > + goto err;
> > +
> > + status = smb_wr16(SECOCEC_ENABLE_REG_1,
> > + val | SECOCEC_ENABLE_REG_1_IR);
> > + if (status != 0)
> > + goto err;
> > +
> > + dev_dbg(dev, "IR enabled");
> > +
> > + status = devm_rc_register_device(dev, cec->irda_rc);
> > +
> > + if (status) {
> > + dev_err(dev, "Failed to prepare input device");
> > + cec->irda_rc = NULL;
> > + goto err;
> > + }
> > +
> > + return 0;
> > +
> > +err:
> > + smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> > +
> > + smb_wr16(SECOCEC_ENABLE_REG_1,
> > + val & ~SECOCEC_ENABLE_REG_1_IR);
> > +
> > + dev_dbg(dev, "IR disabled");
> > + return status;
> > +}
> > +
> > +static int secocec_irda_rx(struct secocec_data *priv)
> > +{
> > + struct secocec_data *cec = priv;
> > + struct device *dev = cec->dev;
> > + u16 val, status, key, addr, toggle;
> > +
> > + if (!cec->irda_rc)
> > + return -ENODEV;
> > +
> > + status = smb_rd16(SECOCEC_IR_READ_DATA, &val);
> > + if (status != 0)
> > + goto err;
> > +
> > + key = val & SECOCEC_IR_COMMAND_MASK;
> > + addr = (val & SECOCEC_IR_ADDRESS_MASK) >> SECOCEC_IR_ADDRESS_SHL;
> > + toggle = (val & SECOCEC_IR_TOGGLE_MASK) >> SECOCEC_IR_TOGGLE_SHL;
> > +
> > + rc_keydown(cec->irda_rc, RC_PROTO_RC5, key, toggle);
>
> Here you are just reported the key, not the address. Please use:
>
> rc_keydown(cec->rc, RC_PROTO_RC5, RC_SCANCODE_RC5(addr, key), toggle);
>
> In fact, you could do:
>
> rc_keydown(cec->rc, RC_PROTO_RC5, val & 0x1f7f, toggle);
>
> I presume the compile is clever enough to fold those shift instructions.

I wondered why the address wasn't used, it had to be together. Thanks. :)

>
> > +
> > + dev_dbg(dev, "IR key pressed: 0x%02x addr 0x%02x toggle 0x%02x", key,
> > + addr, toggle);
> > +
> > + return 0;
> > +
> > +err:
> > + dev_err(dev, "IR Receive message failed (%d)", status);
> > + return -EIO;
> > +}
> > +#else
> > +static void secocec_irda_rx(struct secocec_data *priv)
> > +{
> > +}
> > +
> > +static int secocec_irda_probe(void *priv)
> > +{
> > + return 0;
> > +}
> > +#endif
> > +
> > static irqreturn_t secocec_irq_handler(int irq, void *priv)
> > {
> > struct secocec_data *cec = priv;
> > @@ -420,7 +536,8 @@ static irqreturn_t secocec_irq_handler(int irq, void *priv)
> > if (status_val & SECOCEC_STATUS_REG_1_IR) {
> > dev_dbg(dev, "IR RC5 Interrupt Caught");
> > val |= SECOCEC_STATUS_REG_1_IR;
> > - /* TODO IRDA RX */
> > +
> > + secocec_irda_rx(cec);
> > }
> >
> > /* Reset status register */
> > @@ -595,6 +712,10 @@ static int secocec_probe(struct platform_device *pdev)
> > if (secocec->notifier)
> > cec_register_cec_notifier(secocec->cec_adap, secocec->notifier);
> >
> > + ret = secocec_irda_probe(secocec);
> > + if (ret)
> > + goto err_delete_adapter;
> > +
> > platform_set_drvdata(pdev, secocec);
> >
> > dev_dbg(dev, "Device registered");
> > @@ -614,7 +735,16 @@ static int secocec_probe(struct platform_device *pdev)
> > static int secocec_remove(struct platform_device *pdev)
> > {
> > struct secocec_data *secocec = platform_get_drvdata(pdev);
> > + u16 val;
> > +
> > + if (secocec->irda_rc) {
> > + smb_rd16(SECOCEC_ENABLE_REG_1, &val);
> >
> > + smb_wr16(SECOCEC_ENABLE_REG_1,
> > + val & ~SECOCEC_ENABLE_REG_1_IR);
>
> Those two fit on one line.
>
> > +
> > + dev_dbg(&pdev->dev, "IR disabled");
> > + }
> > cec_unregister_adapter(secocec->cec_adap);
> >
> > if (secocec->notifier)
> > @@ -632,8 +762,8 @@ static int secocec_remove(struct platform_device *pdev)
> > #ifdef CONFIG_PM_SLEEP
> > static int secocec_suspend(struct device *dev)
> > {
> > - u16 val;
> > int status;
> > + u16 val;
> >
> > dev_dbg(dev, "Device going to suspend, disabling");
> >
> > @@ -665,8 +795,8 @@ static int secocec_suspend(struct device *dev)
> >
> > static int secocec_resume(struct device *dev)
> > {
> > - u16 val;
> > int status;
> > + u16 val;
> >
> > dev_dbg(dev, "Resuming device from suspend");
> >
> > diff --git a/drivers/media/platform/seco-cec/seco-cec.h b/drivers/media/platform/seco-cec/seco-cec.h
> > index cc7f0cba8e9e..c00660104a3e 100644
> > --- a/drivers/media/platform/seco-cec/seco-cec.h
> > +++ b/drivers/media/platform/seco-cec/seco-cec.h
> > @@ -101,6 +101,17 @@
> >
> > #define SECOCEC_IR_READ_DATA 0x3e
> >
> > +/*
> > + * IR
> > + */
> > +
> > +#define SECOCEC_IR_COMMAND_MASK 0x007F
> > +#define SECOCEC_IR_COMMAND_SHL 0
> > +#define SECOCEC_IR_ADDRESS_MASK 0x1F00
> > +#define SECOCEC_IR_ADDRESS_SHL 7
> > +#define SECOCEC_IR_TOGGLE_MASK 0x8000
> > +#define SECOCEC_IR_TOGGLE_SHL 15
> > +
> > /*
> > * Enabling register
> > */
> > --
> > 2.18.0
>
> Thanks,
> Sean

Thanks a lot,
Ettore

\
 
 \ /
  Last update: 2018-10-04 23:47    [W:0.074 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site