lkml.org 
[lkml]   [2018]   [Oct]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] clk: qcom: gcc: Add global clock controller driver for QCS404
Hi Stephen,

Thanks for the comments,

On 01-10-18, 10:19, Stephen Boyd wrote:
> Quoting Vinod Koul (2018-09-21 11:59:36)
> > From: Shefali Jain <shefjain@codeaurora.org>
> >
> > Add the clocks supported in global clock controller which clock the
> > peripherals like BLSPs, SDCC, USB, MDSS etc. Register all the clocks
> > to the clock framework for the clients to be able to request for them.
> >
> > Signed-off-by: Shefali Jain <shefjain@codeaurora.org>
> > Signed-off-by: Taniya Das <tdas@codeaurora.org>
> > Co-developed-by: Taniya Das <tdas@codeaurora.org>
> > Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
> > [rebase and tidyup for upstream]
>
> Who did the tidying?

both of us :)

> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > Signed-off-by: Vinod Koul <vkoul@kernel.org>
> > ---
> > - reg : shall contain base register location and length
> > diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
> > index 064768699fe7..529d84cc7503 100644
> > --- a/drivers/clk/qcom/Kconfig
> > +++ b/drivers/clk/qcom/Kconfig
> > @@ -235,6 +235,14 @@ config MSM_GCC_8998
> > Say Y if you want to use peripheral devices such as UART, SPI,
> > i2c, USB, UFS, SD/eMMC, PCIe, etc.
> >
> > +config QCS_GCC_404
> > + tristate "QCS404 Global Clock Controller"
> > + depends on COMMON_CLK_QCOM
> > + help
> > + Support for the global clock controller on QCS404 devices.
> > + Say Y if you want to use peripheral devices such as UART, SPI, I2C,
> > + USB, SD/eMMC, PCIe, etc.
>
> It seems to include multimedia display clks and ethernet? Maybe include
> those too.

Sure will add

> > +#include <linux/kernel.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/clk.h>
>
> Please don't include this.

OK will check if this is required, any reason for not including this?

> > +/* 930MHz configuration */
> > +static const struct alpha_pll_config gpll3_config = {
> > + .l = 48,
> > + .alpha = 0x0,
> > + .alpha_en_mask = BIT(24),
> > + .post_div_mask = 0xf << 8,
> > + .post_div_val = 0x1 << 8,
> > + .vco_mask = 0x3 << 20,
> > + .main_output_mask = 0x1,
> > + .config_ctl_val = 0x4001055b,
> > +};
> > +
> > +static struct pll_vco gpll3_vco[] = {
>
> const?

sure

> > +static struct clk_branch gcc_pwm1_xo512_clk = {
> > + .halt_reg = 0x49004,
> > + .halt_check = BRANCH_HALT,
> > + .clkr = {
> > + .enable_reg = 0x49004,
> > + .enable_mask = BIT(0),
> > + .hw.init = &(struct clk_init_data){
> > + .name = "gcc_pwm1_xo512_clk",
> > + .ops = &clk_branch2_ops,
>
> Do these pwm clks have a parent clk of the XO?

Yes they do

> > + [GCC_USB_HS_PHY_CFG_AHB_CLK] = &gcc_usb_hs_phy_cfg_ahb_clk.clkr,
> > + [GCC_USB_HS_SYSTEM_CLK] = &gcc_usb_hs_system_clk.clkr,
> > + [GFX3D_CLK_SRC] = &gfx3d_clk_src.clkr,
> > + [GP1_CLK_SRC] = &gp1_clk_src.clkr,
>
> Why are some of these missing GCC_ prefix?

will add..

> > +static int gcc_qcs404_probe(struct platform_device *pdev)
> > +{
> > + struct regmap *regmap;
> > + int ret;
> > +
> > + ret = qcom_cc_register_board_clk(&pdev->dev,
> > + "xo_board", "cxo", 19200000);
>
> You shouldn't need to do this. This function is for transitioning DT
> that doesn't have the board clk in DT to something the driver wants to
> use, in this case "cxo". So you can either register a fixed factor 1/1
> clk to do the translation between board and cxo names, or use xo_board
> as the parent of things that can take crystal.

Okay will modify this. If I go about using xo_board as parent, I would
need to register that right? FWIW I see the same thing done in gcc-msm8916

>
> > + if (ret)
> > + return ret;
> > +
> > + regmap = qcom_cc_map(pdev, &gcc_qcs404_desc);
> > + if (IS_ERR(regmap))
> > + return PTR_ERR(regmap);
> > +
> > + clk_alpha_pll_configure(&gpll3_out_main, regmap, &gpll3_config);
> > + clk_set_rate(apss_ahb_clk_src.clkr.hw.clk, 19200000);
>
> use assigned clock rates from DT please.

ok

> > + clk_prepare_enable(apss_ahb_clk_src.clkr.hw.clk);
> > + clk_prepare_enable(gpll0_ao_out_main.clkr.hw.clk);
>
> And these should be marked as critical clocks.

Okay and how do we go about doing that?

> > +#define GCC_USB2A_PHY_SLEEP_CLK 89
> > +#define GCC_USB30_MASTER_CLK 90
> > +#define GCC_USB30_MOCK_UTMI_CLK 91
> > +#define gcc_usb30_sleep_clk 92
> > +#define gcc_usb3_phy_aux_clk 93
> > +#define gcc_usb3_phy_pipe_clk 94
> > +#define gcc_usb_hs_phy_cfg_ahb_clk 95
> > +#define gcc_usb_hs_system_clk 96
> > +#define gfx3d_clk_src 97
> > +#define gp1_clk_src 98
> > +#define gp2_clk_src 99
> > +#define gp3_clk_src 100
> > +#define gpll0_out_main 101
> > +#define gpll1_out_main 102
> > +#define gpll3_out_main 103
> > +#define gpll4_out_main 104
> > +#define hdmi_app_clk_src 105
> > +#define hdmi_pclk_clk_src 106
> > +#define mdp_clk_src 107
> > +#define pcie_0_aux_clk_src 108
> > +#define pcie_0_pipe_clk_src 109
> > +#define pclk0_clk_src 110
> > +#define pdm2_clk_src 111
> > +#define sdcc1_apps_clk_src 112
> > +#define sdcc1_ice_core_clk_src 113
> > +#define sdcc2_apps_clk_src 114
> > +#define usb20_mock_utmi_clk_src 115
> > +#define usb30_master_clk_src 116
> > +#define usb30_mock_utmi_clk_src 117
> > +#define usb3_phy_aux_clk_src 118
> > +#define usb_hs_system_clk_src 119
> > +#define gpll0_ao_clk_src 120
> > +#define wcnss_m_clk 121
> > +#define gcc_usb_hs_inactivity_timers_clk 122
>
> Please capitalize all these macros.

Will do

> > +#define GCC_GENI_IR_BCR 0
> > +#define GCC_USB_HS_BCR 1
> > +#define GCC_USB2_HS_PHY_ONLY_BCR 2
> > +#define GCC_QUSB2_PHY_BCR 3
> > +#define GCC_USB_HS_PHY_CFG_AHB_BCR 4
> > +#define GCC_USB2A_PHY_BCR 5
> > +#define GCC_USB3_PHY_BCR 6
> > +#define GCC_USB_30_BCR 7
> > +#define GCC_USB3PHY_PHY_BCR 8
> > +#define GCC_PCIE_0_BCR 9
> > +#define GCC_PCIE_0_PHY_BCR 10
> > +#define GCC_PCIE_0_LINK_DOWN_BCR 11
> > +#define GCC_PCIEPHY_0_PHY_BCR 12
> > +#define GCC_EMAC_BCR 13
>
> No GDSCs? Ok.

Downstream doesn't seem to have one, will recheck specs.

--
~Vinod

\
 
 \ /
  Last update: 2018-10-03 08:22    [W:0.112 / U:0.648 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site