lkml.org 
[lkml]   [2018]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 25/25] arm64: dts: allwinner: a64-amarula-relic: Enable Techstar TS8550B MIPI-DSI panel
Date
Amarula A64-Relic board by default bound with Techstar TS8550B
MIPI-DSI panel, add support for it.

DSI panel connected via board DSI port with,
- DC1SW as AVDD supply
- DCDC2 as DVDD supply
- DCDC1 as VCC-DSI supply
- PD24 gpio for reset pin
- PD23 gpio for backlight enable pin

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
---
Changes for v3:
- new patch

.../allwinner/sun50i-a64-amarula-relic.dts | 46 +++++++++++++++++++
1 file changed, 46 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index 6cb2b7f0c817..ecc0d8094815 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -9,6 +9,7 @@
#include "sun50i-a64.dtsi"

#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>

/ {
model = "Amarula A64-Relic";
@@ -18,6 +19,14 @@
serial0 = &uart0;
};

+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <1 2 4 8 16 32 64 128 512>;
+ default-brightness-level = <2>;
+ enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PD23 */
+ };
+
chosen {
stdout-path = "serial0:115200n8";
};
@@ -30,6 +39,28 @@
};
};

+&de {
+ status = "okay";
+};
+
+&dphy {
+ status = "okay";
+};
+
+&dsi {
+ vcc-dsi-supply = <&reg_dldo1>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "techstar,ts8550b";
+ reg = <0>;
+ avdd-supply = <&reg_dc1sw>;
+ dvdd-supply = <&reg_dldo2>;
+ reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */
+ backlight = <&backlight>;
+ };
+};
+
&ehci0 {
status = "okay";
};
@@ -72,6 +103,12 @@
status = "okay";
};

+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pin>;
+ status = "okay";
+};
+
&r_rsb {
status = "okay";

@@ -107,6 +144,15 @@
regulator-name = "vcc-pll-avcc";
};

+&reg_dc1sw {
+ /*
+ * This regulator also indirectly drives the PD pingroup GPIOs,
+ * which also controls the power LED.
+ */
+ regulator-always-on;
+ regulator-name = "vcc-phy";
+};
+
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3300000>;
--
2.18.0.321.gffc6fa0e3
\
 
 \ /
  Last update: 2018-10-26 16:47    [W:0.168 / U:1.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site