lkml.org 
[lkml]   [2018]   [Oct]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 2/2] mtd: rawnand: meson: add support for Amlogic NAND flash controller
From
Date


On 2018/10/18 22:24, Boris Brezillon wrote:
> On Thu, 18 Oct 2018 13:09:05 +0800
> Jianxin Pan <jianxin.pan@amlogic.com> wrote:
>
>> +static int meson_nfc_exec_op(struct nand_chip *chip,
>> + const struct nand_operation *op, bool check_only)
>> +{
>> + struct mtd_info *mtd = nand_to_mtd(chip);
>> + struct meson_nfc *nfc = nand_get_controller_data(chip);
>> + const struct nand_op_instr *instr = NULL;
>> + int ret = 0, cmd;
>> + unsigned int op_id;
>> + int i;
>> +
>> + for (op_id = 0; op_id < op->ninstrs; op_id++) {
>> + instr = &op->instrs[op_id];
>> + switch (instr->type) {
>> + case NAND_OP_CMD_INSTR:
>> + if (instr->ctx.cmd.opcode == NAND_CMD_STATUS)
>> + meson_nfc_cmd_idle(nfc, nfc->timing.twb);
>
> Hm, I don't want drivers to base their decisions on the opcode value.
> There's a ->delay_ns field in the instruction object, can't you use
> that one instead? Also, I don't understand why this is only needed for
> the STATUS command. It should normally be applied to all instructions.
>
em, it should be applied to all instructions.
i will fix it and use instr->delay_ns instead.

>> + cmd = nfc->param.chip_select | NFC_CMD_CLE;
>> + cmd |= instr->ctx.cmd.opcode & 0xff;
>> + writel(cmd, nfc->reg_base + NFC_REG_CMD);
>> + if (instr->ctx.cmd.opcode == NAND_CMD_STATUS)
>> + meson_nfc_cmd_idle(nfc, nfc->timing.twhr);
>> + break;
>> +
>> + case NAND_OP_ADDR_INSTR:
>> + for (i = 0; i < instr->ctx.addr.naddrs; i++) {
>> + cmd = nfc->param.chip_select | NFC_CMD_ALE;
>> + cmd |= instr->ctx.addr.addrs[i] & 0xff;
>> + writel(cmd, nfc->reg_base + NFC_REG_CMD);
>> + }
>> + break;
>> +
>> + case NAND_OP_DATA_IN_INSTR:
>> + meson_nfc_read_buf(mtd, instr->ctx.data.buf.in,
>> + instr->ctx.data.len);
>> + break;
>> +
>> + case NAND_OP_DATA_OUT_INSTR:
>> + meson_nfc_write_buf(mtd, instr->ctx.data.buf.out,
>> + instr->ctx.data.len);
>> + break;
>> +
>> + case NAND_OP_WAITRDY_INSTR:
>> + meson_nfc_queue_rb(nfc, instr->ctx.waitrdy.timeout_ms);
>> + break;
>> + }
>> + }
>> + return ret;
>> +}
>
> .
>

\
 
 \ /
  Last update: 2018-10-19 09:29    [W:0.114 / U:6.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site