lkml.org 
[lkml]   [2018]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 4/9] dt-bindings: Add ANX6345 DP/eDP transmitter binding
Date
Hi Icenowy,

On Thursday, 18 October 2018 13:00:05 EEST Icenowy Zheng wrote:
> 在 2018-10-18四的 11:53 +0300,Laurent Pinchart写道:
> > On Thursday, 18 October 2018 10:33:22 EEST Icenowy Zheng wrote:
> >> The ANX6345 is an ultra-low power DisplayPort/eDP transmitter
> >> designed
> >> for portable devices.
> >>
> >> Add a binding document for it.
> >>
> >> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> >> ---
> >>
> >> .../bindings/display/bridge/anx6345.txt | 39 +++++++++++++++++++
> >>
> >> 1 file changed, 39 insertions(+)
> >> create mode 100644
> >>
> >> Documentation/devicetree/bindings/display/bridge/anx6345.txt
> >>
> >> diff --git
> >> a/Documentation/devicetree/bindings/display/bridge/anx6345.txt
> >> b/Documentation/devicetree/bindings/display/bridge/anx6345.txt new
> >> file
> >> mode 100644
> >> index 000000000000..0689d4eb5f65
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/display/bridge/anx6345.txt
> >> @@ -0,0 +1,39 @@
> >> +Analogix ANX6345 eDP Transmitter
> >> +--------------------------------
> >> +
> >> +The ANX6345 is an ultra-low power Full-HD eDP transmitter designed
> >> for
> >> +portable devices.
> >> +
> >> +Required properties:
> >> +
> >> + - compatible : "analogix,anx6345"
> >> + - reg : I2C address of the device
> >> + - reset-gpios : Which GPIO to use for reset
> >> +
> >> +Optional properties:
> >> +
> >> + - dvdd12-supply : Regulator for 1.2V digital core power.
> >> + - dvdd25-supply : Regulator for 2.5V digital core power.
> >
> > Shouldn't these to supplies be mandatory ?
>
> Yes they should.
>
> >> + - panel-supply : Regulator for the power of the panel.
> >
> > Shouldn't the panel supply for specified in the DT node of the panel
> > ?
>
> However, eDP panel can be probed, may vary on the same device, and we
> don't have a generic binding for it...

Shouldn't we fix that ? :-)

> >> + - edid : verbatim EDID data block describing
> >> attached
> >> + panel, only used when the panel has no EDID
> >> info.
> >
> > This should also be specified in the panel DT node.
> >
> > > + - Video port for RGB input, using the DT bindings defined in [1].
> >
> > I think you should also add a port for the output.
>
> What will it point to?

The panel DT node ?

> >> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> >> +
> >> +Example:
> >> +
> >> +anx6345: anx6345@38 {
> >> + compatible = "analogix,anx6345";
> >> + reg = <0x38>;
> >> + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> >> + panel-supply = <&reg_dc1sw>;
> >> + dvdd25-supply = <&reg_dldo2>;
> >> + dvdd12-supply = <&reg_fldo1>;
> >> +
> >> + port {
> >> + anx6345_in: endpoint {
> >> + remote-endpoint = <&tcon0_out_anx6345>;
> >> + };
> >> + };
> >> +};

--
Regards,

Laurent Pinchart



\
 
 \ /
  Last update: 2018-10-18 13:25    [W:0.094 / U:0.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site