lkml.org 
[lkml]   [2018]   [Oct]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 1/2] spi: Add MXIC controller driver
Hi Mason,

On Mon, 15 Oct 2018 16:26:15 +0800
masonccyang@mxic.com.tw wrote:


> +
> +static int mxic_spi_setup(struct spi_device *spi)
> +{
> + return 0;
> +}

Drop this empty function and leave ->setup to NULL.

> +
> +static int mxic_spi_probe(struct platform_device *pdev)
> +{
> + struct spi_master *master;
> + struct resource *res;
> + struct mxic_spi *mxic;
> + int ret;
> +
> + master = spi_alloc_master(&pdev->dev, sizeof(struct mxic_spi));
> + if (!master)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, master);
> +
> + mxic = spi_master_get_devdata(master);
> +
> + master->dev.of_node = pdev->dev.of_node;
> +
> + mxic->ps_clk = devm_clk_get(&pdev->dev, "ps_clk");
> + if (IS_ERR(mxic->ps_clk))
> + return PTR_ERR(mxic->ps_clk);
> +
> + mxic->send_clk = devm_clk_get(&pdev->dev, "send_clk");
> + if (IS_ERR(mxic->send_clk))
> + return PTR_ERR(mxic->send_clk);
> +
> + mxic->send_dly_clk = devm_clk_get(&pdev->dev, "send_dly_clk");
> + if (IS_ERR(mxic->send_dly_clk))
> + return PTR_ERR(mxic->send_dly_clk);
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
> + mxic->regs = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(mxic->regs))
> + return PTR_ERR(mxic->regs);
> +
> + pm_runtime_enable(&pdev->dev);
> + master->auto_runtime_pm = true;
> +
> + master->num_chipselect = 1;
> + master->setup = mxic_spi_setup;
> + master->mem_ops = &mxic_spi_mem_ops;
> +
> + master->set_cs = mxic_spi_set_cs;
> + master->transfer_one = mxic_spi_transfer_one;
> + master->bits_per_word_mask = SPI_BPW_MASK(8);
> + master->mode_bits = SPI_CPOL | SPI_CPHA |
> + SPI_RX_DUAL | SPI_TX_DUAL |
> + SPI_RX_QUAD | SPI_TX_QUAD;
> +
> + mxic_spi_hw_init(mxic);

Don't you need at least the ps_clk to be enabled to write to the MXIC
regs? Also, what happens when the ps_clk is disabled? Is reg content
preserved? If not, then you should probably move the mxic_spi_hw_init()
in the mxic_spi_runtime_resume() function so that you always start from
a known state.

> +
> + ret = spi_register_master(master);
> + if (ret) {
> + dev_err(&pdev->dev, "spi_register_master failed\n");
> + goto err_put_master;
> + }
> +
> + return 0;
> +
> +err_put_master:
> + spi_master_put(master);
> + pm_runtime_disable(&pdev->dev);
> +
> + return ret;
> +}
> +
> +static int mxic_spi_remove(struct platform_device *pdev)
> +{
> + struct spi_master *master = platform_get_drvdata(pdev);
> +
> + pm_runtime_disable(&pdev->dev);
> + spi_unregister_master(master);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id mxic_spi_of_ids[] = {
> + { .compatible = "mxicy,mx25f0a-spi", },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, mxic_spi_of_ids);
> +
> +static struct platform_driver mxic_spi_driver = {
> + .probe = mxic_spi_probe,
> + .remove = mxic_spi_remove,
> + .driver = {
> + .name = "mxic-spi",
> + .of_match_table = mxic_spi_of_ids,
> + .pm = &mxic_spi_dev_pm_ops,
> + },
> +};
> +module_platform_driver(mxic_spi_driver);
> +
> +MODULE_AUTHOR("Mason Yang <masonccyang@mxic.com.tw>");
> +MODULE_DESCRIPTION("MX25F0A SPI controller driver");
> +MODULE_LICENSE("GPL v2");
> +

Drop this blank line.

Regards,

Boris

\
 
 \ /
  Last update: 2018-10-15 10:55    [W:0.071 / U:9.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site