[lkml]   [2018]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
SubjectRe: [LKP] 4ce5f9c9e7 [ 1.323881] WARNING: CPU: 0 PID: 1 at mm/slab_common.c:1031 kmalloc_slab (Eric W. Biederman) writes:

> Sean Christopherson <> writes:
>> On Wed, Oct 10, 2018 at 05:06:52PM -0500, Eric W. Biederman wrote:
>>> (Eric W. Biederman) writes:
>>> > So I am flummoxed. I am reading through the code and I don't see
>>> > anything that could trigger this, and when I ran the supplied reproducer
>>> > it did not reproduce for me.
>>> Even more so. With my tool chain the line that reports the failing
>>> address is impossible.
>>> [ 73.034423] RIP: 0010:copy_siginfo_from_user+0x4d/0xd0
>>> With the supplied configureation my tool chain only has 0x30 bytes for
>>> all of copy_siginfo_from_user. So I can't even begin to guess where
>>> in that function things are failing.
>>> Any additional information that you can provide would be a real help
>>> in tracking down this strange failure.
>> I don't have the exact toolchain, but I was able to get somewhat close
>> and may have found a smoking gun. 0x4d in my build is in the general
>> vicinity of "sig_sicodes[sig].limit" in known_siginfo_layout(). This
>> lines up with the register state from the log, e.g. RDI=0500104d8,
>> which is the mask generated by sig_specific_sicodes. From what I can
>> tell, @sig is never bounds checked. If the compiler generated an AND
>> instruction to compare against sig_specific_sicodes then that could
>> resolve true with any arbitrary value that happened to collide with
>> sig_specific_sicodes and result in an out-of-bounds access to
>> @sig_sicodes. siginfo_layout() for example explicitly checks @sig
>> before indexing @sig_sicode, e.g. "sig < ARRAY_SIZE(sig_sicodes)".
>> Maybe this?
> But sig is bounds checked. Even better sig is checked to see if it
> is one of the values in the array.
>> From include/linux/signal.h
> rt_sigmask(SIGILL) | rt_sigmask(SIGFPE) | \
> rt_sigmask(SIGSEGV) | rt_sigmask(SIGBUS) | \
> rt_sigmask(SIGTRAP) | rt_sigmask(SIGCHLD) | \
> rt_sigmask(SIGPOLL) | rt_sigmask(SIGSYS) | \
> #define siginmask(sig, mask) \
> ((sig) < SIGRTMIN && (rt_sigmask(sig) & (mask)))
> #define sig_specific_sicodes(sig) siginmask(sig, SIG_SPECIFIC_SICODES_MASK)
> Hmm. I wonder if something is passing in a negative signal number.
> There is not a bounds check for that. A sufficiently large signal
> number might be the problem here. Yes. I can get an oops with
> a sufficiently large negative signal number.
> The code will later call valid_signal in check_permissions and
> that will cause the system call to fail, so the issue is just that
> the signal number is not being validated early enough.
> On the output path (copy_siginfo_to_user and copy_siginfo_to_user32) the
> signal number should be validated before it ever reaches userspace
> which is why I expect trinity never triggered anything.
> There is copy_siginfo_from_user32 and that does call siginfo_layout with
> a possibly negative signal number. Which has the same potential issues.
> So I am going to go with the fix below. That fixes things in my testing
> and by being unsigned should fix keep negative numbers from being a
> problem.

Sean thank you very much for putting me on the right path to track this
failing test down.


 \ /
  Last update: 2018-10-11 03:15    [W:0.066 / U:2.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site