[lkml]   [2018]   [Jan]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v4 0/2] kprobes: improve error handling when arming/disarming kprobes

This patchset attempts to improve error handling when arming or disarming
ftrace-based kprobes. The current behavior is to simply WARN when ftrace
(un-)registration fails, without propagating the error code. This can lead
to confusing situations where, for example, register_kprobe()/enable_kprobe()
would return 0 indicating success even if arming via ftrace had failed. In
this scenario we'd end up with a non-functioning kprobe even though kprobe
registration (or enablement) returned success. In this patchset, we take
errors from ftrace into account and propagate the error when we cannot arm
or disarm a kprobe.

Below is an example that illustrates the problem using livepatch and
systemtap (which uses kprobes underneath). Both livepatch and kprobes use
ftrace ops with the IPMODIFY flag set, so registration at the same
function entry is limited to only one ftrace user.

# modprobe livepatch-sample # patches cmdline_proc_show, ftrace ops has IPMODIFY set
# stap -e 'probe kernel.function("cmdline_proc_show").call { printf ("cmdline_proc_show\n"); }'

.. (nothing prints after reading /proc/cmdline) ..

The systemtap handler doesn't execute due to a kprobe arming failure caused
by a ftrace IPMODIFY conflict with livepatch, and there isn't an obvious
indication of error from systemtap (because register_kprobe() returned
success) unless the user inspects dmesg.

# modprobe livepatch-sample
# stap -e 'probe kernel.function("cmdline_proc_show").call { printf ("cmdline_proc_show\n"); }'
WARNING: probe kernel.function("cmdline_proc_show@/home/jeyu/work/linux-next/fs/proc/cmdline.c:6").call (address 0xffffffffa82fe910) registration error (rc -16)

Although the systemtap handler doesn't execute (as it shouldn't), the
ftrace error is propagated and now systemtap prints a visible error message
stating that (kprobe) registration had failed (because register_kprobe()
returned an error), along with the propagated error code.

This patchset was based on Petr Mladek's original patchset (patches 2 and 3)
back in 2015, which improved kprobes error handling, found here:

However, further work on this had been paused since then and the patches
were not upstreamed.

This patchset has been lightly sanity-tested (on linux-next) with kprobes,
kretprobes, and optimized kprobes. It passes the kprobes smoke test, but
more testing is greatly appreciated.

Changes from v3:
- Have (dis)arm_kprobe_ftrace() return -ENODEV instead of 0 in case of
- Add total count of all probes tried in (dis)arm_all_kprobes()

Changes from v2:
- Add missing synchronize rcu in register_aggr_kprobe()
- s/kprobes/probes/ on error message in (dis)arm_all_kprobes()

Changes from v1:
- Don't arm the kprobe before adding it to the kprobe table, otherwise
we'll temporarily see a stray breakpoint.
- Remove kprobe from the kprobe_table and call synchronize_sched() if
arming during register_kprobe() fails.
- add Masami's ack on the 2nd patch (unchanged from v1)

Jessica Yu (2):
kprobes: propagate error from arm_kprobe_ftrace()
kprobes: propagate error from disarm_kprobe_ftrace()

kernel/kprobes.c | 174 +++++++++++++++++++++++++++++++++++++++----------------
1 file changed, 124 insertions(+), 50 deletions(-)


 \ /
  Last update: 2018-01-14 23:16    [W:0.025 / U:10.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site