[lkml]   [2017]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v3 0/3] mmc: Add OMAP SDHCI driver
This is the first step in deprecating omap_hsmmc driver completely
and moving to sdhci-omap driver which uses the sdhci library.

This patch that adds a new SDHCI quirk "MMC_RSP_136" has already been
merged and hence removed it in this revision.

Apart from the quirk, sdhci-omap has it's own callbacks
to set_clock (clock divider programming is different from generic sdhci)
, set_power, set_bus_width, set_bus_mode and platform_send_init_74_clocks.
These callback functions are implemented based on omap_hsmmc driver.
Since sdhci-omap driver requires pbias regulator fixes to be present, I've
sent them as part of this series.

The sdhci-omap driver supports only the high speed mode and UHS/HS200
mode will be added in a later series.

It has been tested only in boards having DRA7 SoCs like dra7-evm, dra72-evm,
am571x-idk, am572x-idk, am57xx-evm. (Tested only eMMC and SD.
SDIO support will be added later). The plan is to fully convert DRA7
SoC to use SDHCI driver and then convert other legacy platforms to use

For sdhci-omap to be functional, the following tag should be merged (There
are no compilation dependencies).

However the above regulator tag will impact omap_hsmmc driver. so [1]
should be merged before everything else is merged.

[1] ->

The patch to add config and dts changes to use sdhci-omap will be sent

Next Steps:
*) Add UHS support to sdhci-omap
*) Add SDIO support
*) Add support for older TI platforms

Changes from v3:
*) removed omap_hsmmc and pbias-regulator patches from the series
*) Fixed dt-binding documentation (remove '0x' in node name)
*) stop clock if MMC core sends '0' in frequency

Changes from v2:
*) Rebased on git:// next
*) Included a couple of patches from Ravikumar to fix pbias-regulator driver
to support max-voltage of 3.3V. This is required for sdhci-omap driver.
*) Create sdhci-omap as a new driver with MMC generic bindings and hence doesn't
have bindings like ti,dual-volt added for omap-hsmmc. (Instead of
ti,dual-volt, sdhci-omap driver uses the supported regulator voltage to
set controller IO voltage capabilities).
When omap-hsmmc driver is deprecated, support for these properties will
be added to sdhci-omap.
*) Fixed minor comments from Adrian).

Changes from v1:
*) Remove the quirks and instead use sdhci_omap specific callbacks for
set_power, set_busmode etc.
*) Add a patch from Adrian to tidy reading 136-bit responses

I've also pushed the entire series along with dependent dt patches @ sdhci_v3 (in case someone
wants to test)

Kishon Vijay Abraham I (3):
dt-bindings: sdhci-omap: Add bindings for the sdhci-omap controller
mmc: sdhci-omap: Add OMAP SDHCI driver

.../devicetree/bindings/mmc/sdhci-omap.txt | 16 +
drivers/mmc/host/Kconfig | 12 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-omap.c | 607 +++++++++++++++++++++
5 files changed, 642 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-omap.txt
create mode 100644 drivers/mmc/host/sdhci-omap.c


 \ /
  Last update: 2017-09-06 13:49    [W:0.117 / U:0.988 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site