lkml.org 
[lkml]   [2017]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] doc: coresight: correct usage for disabling idle states
On Tue, Sep 19, 2017 at 03:32:54PM -0600, Mathieu Poirier wrote:
> On 15 September 2017 at 04:16, Leo Yan <leo.yan@linaro.org> wrote:
> > In the coresight CPU debug document it suggests to use 'echo' command
> > to set latency request to /dev/cpu_dma_latency so can disable all CPU
> > idle states, but in fact this doesn't work.
> >
> > This is because when the command 'echo' exits, it releases the device
> > node's file descriptor and the kernel release function removes the QoS
> > constraint; finally when the command 'echo' finished there have no
> > constraint imposed on cpu_dma_latency.
> >
> > This patch changes to use 'exec' to access '/dev/cpu_dma_latency', the
> > command 'exec' can avoid the file descriptor to be closed so we can
> > keep the constraint on cpu_dma_latency.
> >
> > This patch also adds the info for reference docs for PM QoS and cpuidle
> > sysfs.
> >
> > Cc: Jonathan Corbet <corbet@lwn.net>
> > Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
> > Cc: Sudeep Holla <sudeep.holla@arm.com>
> > Reported-by: Kim Phillips <kim.phillips@arm.com>
> > Signed-off-by: Leo Yan <leo.yan@linaro.org>
> > ---
> > Documentation/trace/coresight-cpu-debug.txt | 14 +++++++++-----
> > 1 file changed, 9 insertions(+), 5 deletions(-)
> >
> > diff --git a/Documentation/trace/coresight-cpu-debug.txt b/Documentation/trace/coresight-cpu-debug.txt
> > index b3da1f9..205ff95 100644
> > --- a/Documentation/trace/coresight-cpu-debug.txt
> > +++ b/Documentation/trace/coresight-cpu-debug.txt
> > @@ -149,11 +149,15 @@ If you want to limit idle states at boot time, you can use "nohlt" or
> >
> > At the runtime you can disable idle states with below methods:
> >
> > -Set latency request to /dev/cpu_dma_latency to disable all CPUs specific idle
> > -states (if latency = 0uS then disable all idle states):
> > -# echo "what_ever_latency_you_need_in_uS" > /dev/cpu_dma_latency
> > -
> > -Disable specific CPU's specific idle state:
> > +By using PM QoS interface '/dev/cpu_dma_latency', we can set latency
> > +constraint to disable all CPUs specific idle states (see
> > +Documentation/power/pm_qos_interface.txt, section 'From user mode');
> > +below is one example to set latency constraint to '00000000', it is
> > +hexadecimal format with microsecond unit:
> > +# exec 3<> /dev/cpu_dma_latency; echo '00000000' >&3
>
> Since doing echo '00000000' >&3 or simply echo 0 >&3 yields the same
> result I would go for the latter. I also think it is important to
> specify that using an "echo" command without holding the file open
> won't give the desired result. I would reformat your paragraph as
> follow:
>
> >>> Begin >>>
>
> It is possible to disable CPU idle states by way of the PM QoS
> subsystem, more specifically by using the "/dev/cpu_dma_latency"
> interface (see Documentation/power/pm_qos_interface.txt for more
> details). As specified in the PM QoS documentation the requested
> parameter will stay in effect until the file descriptor is released.
> For example:
>
> # exec 3<> /dev/cpu_dma_latency; echo 0 >&3
> ...
> Do some work...
> ...
> # exec 3<>-
>
> The same can also be done from an application program.
>
> <<< End <<<

Very appreciate your rephasing and reviewing. Will spin a new patch
with it.

Thanks,
Leo Yan

> > +
> > +Disable specific CPU's specific idle state from cpuidle sysfs (see
> > +Documentation/cpuidle/sysfs.txt):
> > # echo 1 > /sys/devices/system/cpu/cpu$cpu/cpuidle/state$state/disable
> >
> >
> > --
> > 2.7.4
> >

\
 
 \ /
  Last update: 2017-09-20 00:31    [W:0.050 / U:1.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site