lkml.org 
[lkml]   [2017]   [Aug]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] net: dsa: mediatek: add adjust link support for user ports
Date
Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.

Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
---
drivers/net/dsa/mt7530.c | 38 ++++++++++++++++++++++++++++++++++++++
drivers/net/dsa/mt7530.h | 1 +
2 files changed, 39 insertions(+)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 1e46418a3b74..264b281eb86b 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -625,6 +625,44 @@ static void mt7530_adjust_link(struct dsa_switch *ds, int port,
* all finished.
*/
mt7623_pad_clk_setup(ds);
+ } else {
+ u16 lcl_adv = 0, rmt_adv = 0;
+ u8 flowctrl;
+ u32 mcr = PMCR_USERP_LINK | PMCR_FORCE_MODE;
+
+ switch (phydev->speed) {
+ case SPEED_1000:
+ mcr |= PMCR_FORCE_SPEED_1000;
+ break;
+ case SPEED_100:
+ mcr |= PMCR_FORCE_SPEED_100;
+ break;
+ };
+
+ if (phydev->link)
+ mcr |= PMCR_FORCE_LNK;
+
+ if (phydev->duplex) {
+ mcr |= PMCR_FORCE_FDX;
+
+ if (phydev->pause)
+ rmt_adv = LPA_PAUSE_CAP;
+ if (phydev->asym_pause)
+ rmt_adv |= LPA_PAUSE_ASYM;
+
+ if (phydev->advertising & ADVERTISED_Pause)
+ lcl_adv |= ADVERTISE_PAUSE_CAP;
+ if (phydev->advertising & ADVERTISED_Asym_Pause)
+ lcl_adv |= ADVERTISE_PAUSE_ASYM;
+
+ flowctrl = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv);
+
+ if (flowctrl & FLOW_CTRL_TX)
+ mcr |= PMCR_TX_FC_EN;
+ if (flowctrl & FLOW_CTRL_RX)
+ mcr |= PMCR_RX_FC_EN;
+ }
+ mt7530_write(priv, MT7530_PMCR_P(port), mcr);
}
}

diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index b83d76b99802..74db9822eb40 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -151,6 +151,7 @@ enum mt7530_stp_state {
#define PMCR_TX_FC_EN BIT(5)
#define PMCR_RX_FC_EN BIT(4)
#define PMCR_FORCE_SPEED_1000 BIT(3)
+#define PMCR_FORCE_SPEED_100 BIT(2)
#define PMCR_FORCE_FDX BIT(1)
#define PMCR_FORCE_LNK BIT(0)
#define PMCR_COMMON_LINK (PMCR_IFG_XMIT(1) | PMCR_MAC_MODE | \
--
2.11.0
\
 
 \ /
  Last update: 2017-08-07 16:21    [W:0.059 / U:2.192 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site