lkml.org 
[lkml]   [2017]   [Jul]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.9 147/172] ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
Date
4.9-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Dave Gerlach <d-gerlach@ti.com>

commit 04abaf07f6d5cdf22b7a478a86e706dfeeeef960 upstream.

Starting from commit 5de85b9d57ab ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind") pm_runtime core now changes
device runtime_status back to after RPM_SUSPENDED after a probe defer.
Certain OMAP devices make use of "ti,no-idle-on-init" flag which causes
omap_device_enable to be called during the BUS_NOTIFY_ADD_DEVICE event
during probe, along with pm_runtime_set_active.

This call to pm_runtime_set_active typically will prevent a call to
pm_runtime_get in a driver probe function from re-enabling the
omap_device. However, in the case of a probe defer that happens before
the driver probe function is able to run, such as a missing pinctrl
states defer, pm_runtime_reinit will set the device as RPM_SUSPENDED and
then once driver probe is actually able to run, pm_runtime_get will see
the device as suspended and call through to the omap_device layer,
attempting to enable the already enabled omap_device and causing errors
like this:

omap-gpmc 50000000.gpmc: omap_device: omap_device_enable() called from
invalid state 1
omap-gpmc 50000000.gpmc: use pm_runtime_put_sync_suspend() in driver?

We can avoid this error by making sure the pm_runtime status of a device
matches the omap_device state before a probe attempt. By extending the
omap_device bus notifier to act on the BUS_NOTIFY_BIND_DRIVER event we
can check if a device is enabled in omap_device but with a pm_runtime
status of RPM_SUSPENDED and once again mark the device as RPM_ACTIVE to
avoid a second incorrect call to omap_device_enable.

Fixes: 5de85b9d57ab ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
arch/arm/mach-omap2/omap_device.c | 8 ++++++++
1 file changed, 8 insertions(+)

--- a/arch/arm/mach-omap2/omap_device.c
+++ b/arch/arm/mach-omap2/omap_device.c
@@ -222,6 +222,14 @@ static int _omap_device_notifier_call(st
dev_err(dev, "failed to idle\n");
}
break;
+ case BUS_NOTIFY_BIND_DRIVER:
+ od = to_omap_device(pdev);
+ if (od && (od->_state == OMAP_DEVICE_STATE_ENABLED) &&
+ pm_runtime_status_suspended(dev)) {
+ od->_driver_status = BUS_NOTIFY_BIND_DRIVER;
+ pm_runtime_set_active(dev);
+ }
+ break;
case BUS_NOTIFY_ADD_DEVICE:
if (pdev->dev.of_node)
omap_device_build_from_dt(pdev);

\
 
 \ /
  Last update: 2017-07-03 15:46    [W:0.622 / U:0.080 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site