lkml.org 
[lkml]   [2017]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH RFC 2/2] dt-bindings: add binding documentation for Allwinner CSI
On Fri, Jun 30, 2017 at 5:19 AM, Rob Herring <robh@kernel.org> wrote:
> On Tue, Jun 27, 2017 at 07:07:34PM +0800, Yong Deng wrote:
>> Add binding documentation for Allwinner CSI.
>
> For the subject:
>
> dt-bindings: media: Add Allwinner Camera Sensor Interface (CSI)
>
> "binding documentation" is redundant.
>
>>
>> Signed-off-by: Yong Deng <yong.deng@magewell.com>
>> ---
>> .../devicetree/bindings/media/sunxi-csi.txt | 51 ++++++++++++++++++++++
>> 1 file changed, 51 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/media/sunxi-csi.txt
>>
>> diff --git a/Documentation/devicetree/bindings/media/sunxi-csi.txt b/Documentation/devicetree/bindings/media/sunxi-csi.txt
>> new file mode 100644
>> index 0000000..770be0e
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/sunxi-csi.txt
>> @@ -0,0 +1,51 @@
>> +Allwinner V3s Camera Sensor Interface
>> +------------------------------
>> +
>> +Required properties:
>> + - compatible: value must be "allwinner,sun8i-v3s-csi"
>> + - reg: base address and size of the memory-mapped region.
>> + - interrupts: interrupt associated to this IP
>> + - clocks: phandles to the clocks feeding the CSI
>> + * ahb: the CSI interface clock
>> + * mod: the CSI module clock
>> + * ram: the CSI DRAM clock
>> + - clock-names: the clock names mentioned above
>> + - resets: phandles to the reset line driving the CSI
>> +
>> +- ports: A ports node with endpoint definitions as defined in
>> + Documentation/devicetree/bindings/media/video-interfaces.txt. The
>> + first port should be the input endpoints, the second one the outputs
>
> Is there more than one endpoint for each port? If so, need to define
> that numbering too.

It is possible to have multiple camera sensors connected to the same
bus. Think front and back cameras on a cell phone or tablet.

I don't think any kind of numbering makes much sense though. The
system is free to use just one sensor at a time, or use many with
some time multiplexing scheme. What might matter to the end user
is where the camera is placed. But using the position or orientation
as a numbering scheme might not work well either. Someone may end
up using two sensors with the same orientation for stereoscopic
vision.

>
>> +
>> +Example:
>> +
>> + csi1: csi@01cb4000 {
>> + compatible = "allwinner,sun8i-v3s-csi";
>> + reg = <0x01cb4000 0x1000>;

Yong, the address range size is 0x4000, including the CCI (I2C)
controller at offset 0x3000. You should also consider this in
the device tree binding, and the driver.

ChenYu

>> + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&ccu CLK_BUS_CSI>,
>> + <&ccu CLK_CSI1_SCLK>,
>> + <&ccu CLK_DRAM_CSI>;
>> + clock-names = "ahb", "mod", "ram";
>> + resets = <&ccu RST_BUS_CSI>;
>> +
>> + port {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + /* Parallel bus endpoint */
>> + csi1_0: endpoint@0 {
>> + reg = <0>;
>
> Don't need this and everything associated with it for a single endpoint.
>
>> + remote = <&adv7611_1>;
>> + bus-width = <16>;
>> + data-shift = <0>;
>> +
>> + /* If hsync-active/vsync-active are missing,
>> + embedded BT.656 sync is used */
>> + hsync-active = <0>; /* Active low */
>> + vsync-active = <0>; /* Active low */
>> + data-active = <1>; /* Active high */
>> + pclk-sample = <1>; /* Rising */
>> + };
>> + };
>> + };
>> +
>> --
>> 1.8.3.1
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html

\
 
 \ /
  Last update: 2017-06-30 05:42    [W:0.071 / U:0.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site