lkml.org 
[lkml]   [2017]   [Feb]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v13 00/12] power: add power sequence library
From
Date
Peter,

On 11/02/17 03:27, Peter Chen wrote:
> Hi all,
>
> This is a follow-up for my last power sequence framework patch set [1].
> According to Rob Herring and Ulf Hansson's comments[2]. The kinds of
> power sequence instances will be added at postcore_initcall, the match
> criteria is compatible string first, if the compatible string is not
> matched between dts and library, it will try to use generic power sequence.
>
> The host driver just needs to call of_pwrseq_on/of_pwrseq_off
> if only one power sequence instance is needed, for more power sequences
> are used, using of_pwrseq_on_list/of_pwrseq_off_list instead (eg, USB hub driver).
>
> In future, if there are special power sequence requirements, the special
> power sequence library can be created.
>
> This patch set is tested on i.mx6 sabresx evk using a dts change, I use
> two hot-plug devices to simulate this use case, the related binding
> change is updated at patch [1/6], The udoo board changes were tested
> using my last power sequence patch set.[3]
>
> Except for hard-wired MMC and USB devices, I find the USB ULPI PHY also
> need to power on itself before it can be found by ULPI bus.

Can patches 3-7 can be sent independently of the power related patches?

cheers,
-roger

>
> Changes for v13:
> - Add more design descriptions at design doc and fix one build error
> introduced by v12 wrongly [Patch 2/12]
> - Add the last three dts patches which were forgotten at last series
> - Move the comment for usb_create_shared_hcd to correct place [Patch 3/12]
> - Add sysdev for shared hcd too for xhci-plat.c [Patch 6/12]
>
> Rafael, if the first two power sequence patches are ok for you, would you consider
> accept these first, the other USB patches can go through USB tree at v4.12-rc1?
>
> Changes for v12:
> - Add design doc and more comments at generic power sequence source file [Patch 2/9]
> - Introduce four Arnd Bergmann patches and one my ehci related patches, these patches
> are used to get property DT/firmware information at USB code, and these information
> are needed for power sequence operation at USB. With these five patches, my chipidea
> hack patch in previous patch set can be removed. [Patch 3-7/9]
> - Add -ENOENT judgement to avoid USB error if no power sequence library is chosen [9/9]
>
> Changes for v11:
> - Fix warning: (USB) selects POWER_SEQUENCE which has unmet direct dependencies (OF)
> - Delete redundant copyright statement.
> - Change pr_warn to pr_debug at wrseq_find_available_instance
> - Refine kerneldoc
> - %s/ENONET/ENOENT
> - Allocate pwrseq list node before than carry out power sequence on
> - Add mutex_lock/mutex_lock for pwrseq node browse at pwrseq_find_available_instance
> - Add pwrseq_suspend/resume for API both single instance and list
> - Add .pwrseq_suspend/resume for pwrseq_generic.c
> - Add pwrseq_suspend_list and pwrseq_resume_list for USB hub suspend
> and resume routine
>
> Changes for v10:
> - Improve the kernel-doc for power sequence core, including exported APIs and
> main structure. [Patch 2/8]
> - Change Kconfig, and let the user choose power sequence. [Patch 2/8]
> - Delete EXPORT_SYMBOL and change related APIs as local, these APIs do not
> be intended to export currently. [Patch 2/8]
> - Selete POWER_SEQUENCE at USB core's Kconfig. [Patch 4/8]
>
> Changes for v9:
> - Add Vaibhav Hiremath's reviewed-by [Patch 4/8]
> - Rebase to v4.9-rc1
>
> Changes for v8:
> - Allocate one extra pwrseq instance if pwrseq_get has succeed, it can avoid
> preallocate instances problem which the number of instance is decided at
> compile time, thanks for Heiko Stuebner's suggestion [Patch 2/8]
> - Delete pwrseq_compatible_sample.c which is the demo purpose to show compatible
> match method. [Patch 2/8]
> - Add Maciej S. Szmigiero's tested-by. [Patch 7/8]
>
> Changes for v7:
> - Create kinds of power sequence instance at postcore_initcall, and match
> the instance with node using compatible string, the beneit of this is
> the host driver doesn't need to consider which pwrseq instance needs
> to be used, and pwrseq core will match it, however, it eats some memories
> if less power sequence instances are used. [Patch 2/8]
> - Add pwrseq_compatible_sample.c to test match pwrseq using device_id. [Patch 2/8]
> - Fix the comments Vaibhav Hiremath adds for error path for clock and do not
> use device_node for parameters at pwrseq_on. [Patch 2/8]
> - Simplify the caller to use power sequence, follows Alan's commnets [Patch 4/8]
> - Tested three pwrseq instances together using both specific compatible string and
> generic libraries.
>
> Changes for v6:
> - Add Matthias Kaehlcke's Reviewed-by and Tested-by. (patch [2/6])
> - Change chipidea core of_node assignment for coming user. (patch [5/6])
> - Applies Joshua Clayton's three dts changes for two boards,
> the USB device's reg has only #address-cells, but without #size-cells.
>
> Changes for v5:
> - Delete pwrseq_register/pwrseq_unregister, which is useless currently
> - Fix the linker error when the pwrseq user is compiled as module
>
> Changes for v4:
> - Create the patch on next-20160722
> - Fix the of_node is not NULL after chipidea driver is unbinded [Patch 5/6]
> - Using more friendly wait method for reset gpio [Patch 2/6]
> - Support multiple input clocks [Patch 2/6]
> - Add Rob Herring's ack for DT changes
> - Add Joshua Clayton's Tested-by
>
> Changes for v3:
> - Delete "power-sequence" property at binding-doc, and change related code
> at both library and user code.
> - Change binding-doc example node name with Rob's comments
> - of_get_named_gpio_flags only gets the gpio, but without setting gpio flags,
> add additional code request gpio with proper gpio flags
> - Add Philipp Zabel's Ack and MAINTAINER's entry
>
> Changes for v2:
> - Delete "pwrseq" prefix and clock-names for properties at dt binding
> - Should use structure not but its pointer for kzalloc
> - Since chipidea core has no of_node, let core's of_node equals glue
> layer's at core's probe
>
> [1] http://www.spinics.net/lists/linux-usb/msg142755.html
> [2] http://www.spinics.net/lists/linux-usb/msg143106.html
> [3] http://www.spinics.net/lists/linux-usb/msg142815.html
> [4] http://www.spinics.net/lists/linux-usb/msg152375.html
>
> Arnd Bergmann (4):
> usb: separate out sysdev pointer from usb_bus
> usb: chipidea: use bus->sysdev for DMA configuration
> usb: ehci: fsl: use bus->sysdev for DMA configuration
> usb: xhci: use bus->sysdev for DMA configuration
>
> Joshua Clayton (2):
> ARM: dts: imx6qdl: Enable usb node children with <reg>
> ARM: dts: imx6q-evi: Fix onboard hub reset line
>
> Peter Chen (6):
> binding-doc: power: pwrseq-generic: add binding doc for generic power
> sequence library
> power: add power sequence library
> usb: ehci: use bus->sysdev for DMA configuration
> binding-doc: usb: usb-device: add optional properties for power
> sequence
> usb: core: add power sequence handling for USB devices
> ARM: dts: imx6qdl-udoo.dtsi: fix onboard USB HUB property
>
> .../bindings/power/pwrseq/pwrseq-generic.txt | 48 +++
> .../devicetree/bindings/usb/usb-device.txt | 10 +-
> Documentation/power/power-sequence/design.rst | 54 ++++
> MAINTAINERS | 9 +
> arch/arm/boot/dts/imx6q-evi.dts | 25 +-
> arch/arm/boot/dts/imx6qdl-udoo.dtsi | 26 +-
> arch/arm/boot/dts/imx6qdl.dtsi | 6 +
> drivers/power/Kconfig | 1 +
> drivers/power/Makefile | 1 +
> drivers/power/pwrseq/Kconfig | 20 ++
> drivers/power/pwrseq/Makefile | 2 +
> drivers/power/pwrseq/core.c | 335 +++++++++++++++++++++
> drivers/power/pwrseq/pwrseq_generic.c | 234 ++++++++++++++
> drivers/usb/Kconfig | 1 +
> drivers/usb/chipidea/core.c | 3 -
> drivers/usb/chipidea/host.c | 3 +-
> drivers/usb/chipidea/udc.c | 10 +-
> drivers/usb/core/buffer.c | 12 +-
> drivers/usb/core/hcd.c | 80 ++---
> drivers/usb/core/hub.c | 49 ++-
> drivers/usb/core/hub.h | 1 +
> drivers/usb/core/usb.c | 18 +-
> drivers/usb/host/ehci-fsl.c | 4 +-
> drivers/usb/host/ehci-mem.c | 12 +-
> drivers/usb/host/xhci-mem.c | 12 +-
> drivers/usb/host/xhci-plat.c | 35 ++-
> drivers/usb/host/xhci.c | 15 +-
> include/linux/power/pwrseq.h | 81 +++++
> include/linux/usb.h | 1 +
> include/linux/usb/hcd.h | 3 +
> 30 files changed, 990 insertions(+), 121 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> create mode 100644 Documentation/power/power-sequence/design.rst
> create mode 100644 drivers/power/pwrseq/Kconfig
> create mode 100644 drivers/power/pwrseq/Makefile
> create mode 100644 drivers/power/pwrseq/core.c
> create mode 100644 drivers/power/pwrseq/pwrseq_generic.c
> create mode 100644 include/linux/power/pwrseq.h
>

--
cheers,
-roger

\
 
 \ /
  Last update: 2017-02-14 19:07    [W:0.226 / U:2.360 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site