lkml.org 
[lkml]   [2017]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 01/10] dt-bindings: media: Add Renesas CEU bindings
Date
Add bindings documentation for Renesas Capture Engine Unit (CEU).

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
.../devicetree/bindings/media/renesas,ceu.txt | 87 ++++++++++++++++++++++
1 file changed, 87 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/renesas,ceu.txt

diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
new file mode 100644
index 0000000..a88e9cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
@@ -0,0 +1,87 @@
+Renesas Capture Engine Unit (CEU)
+----------------------------------------------
+
+The Capture Engine Unit is the image capture interface found on Renesas
+RZ chip series and on SH Mobile ones.
+
+The interface supports a single parallel input with up 8/16bits data bus width.
+
+Required properties:
+- compatible
+ Must be "renesas,renesas-ceu".
+- reg
+ Physical address base and size.
+- interrupts
+ The interrupt line number.
+- pinctrl-names, pinctrl-0
+ phandle of pin controller sub-node configuring pins for CEU operations.
+
+CEU supports a single parallel input and should contain a single 'port' subnode
+with a single 'endpoint'. Optional endpoint properties applicable to parallel
+input bus are described in "video-interfaces.txt".
+
+Example:
+
+The example describes the connection between the Capture Engine Unit and a
+OV7670 image sensor sitting on bus i2c1 with an on-board 24Mhz clock.
+
+ceu: ceu@e8210000 {
+ reg = <0xe8210000 0x209c>;
+ compatible = "renesas,renesas-ceu";
+ interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vio_pins>;
+
+ status = "okay";
+
+ port {
+ ceu_in: endpoint {
+ remote-endpoint = <&ov7670_out>;
+
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pclk-sample = <1>;
+ data-active = <1>;
+ };
+ };
+};
+
+i2c1: i2c@fcfee400 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ ov7670: camera@21 {
+ compatible = "ovti,ov7670";
+ reg = <0x21>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&vio_pins>;
+
+ reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
+ powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
+
+ clocks = <&xclk>;
+ clock-names = "xclk";
+
+ xclk: fixed_clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ port {
+ ov7670_out: endpoint {
+ remote-endpoint = <&ceu_in>;
+
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pclk-sample = <1>;
+ data-active = <1>;
+ };
+ };
+ };
--
2.7.4
\
 
 \ /
  Last update: 2017-11-15 12:15    [W:0.247 / U:2.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site