lkml.org 
[lkml]   [2016]   [Nov]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/3] binding: irqchip: mtk-cirq: Add binding document
From
Date
On Wed, 2016-11-09 at 12:26 -0600, Rob Herring wrote:
> On Tue, Nov 01, 2016 at 07:52:00PM +0800, Youlin Pei wrote:
> > This commit adds the device tree binding document for
> > the mediatek cirq.
> >
> > Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
> > ---
> > .../interrupt-controller/mediatek,cirq.txt | 30 ++++++++++++++++++++
> > 1 file changed, 30 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/interrupt-controller/mediatek,cirq.txt
> >
> > diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,cirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,cirq.txt
> > new file mode 100644
> > index 0000000..84e8123
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,cirq.txt
> > @@ -0,0 +1,30 @@
> > +* Mediatek 27xx cirq
> > +
> > +In Mediatek SOCs, the CIRQ is a low power interrupt controller designed to
> > +works outside MCUSYS which comprises with Cortex-Ax cores,CCI and GIC.
>
> s/works/work/

will fix in next version.

>
> > +The external interrupts (outside MCUSYS) will feed through CIRQ and connect
> > +to GIC in MCUSYS. When CIRQ is enabled, it will record the edge-sensitive
> > +interrupts and generated a pulse signal to parent interrupt controller when
>
> s/generated/generate/

will fix in next version.

>
> > +flush command is executed. With CIRQ, MCUSYS can be completely turned off
> > +to improve the system power consumption without losing interrupts.
> > +
> > +Required properties:
> > +- compatible: should be: "mediatek,mtk-cirq".
>
> This should be SoC specific. This is fine as a fallback if the same
> block is in many SoCs, but mediatek and mtk is a bit redundant.
>

In next version, i will improve as following:
- compatible: Should be one of
- "mediatek,mt2701-cirq" for mt2701 CIRQ
- "mediatek,mt8173-cirq" for mt8173 CIRQ
- "mediatek,mt8135-cirq" for mt8135 CIRQ
and "mediatek,cirq" as a fallback.

> > +- interrupt-controller : Identifies the node as an interrupt controller.
> > +- #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
> > +- interrupt-parent: phandle of irq parent for cirq. The parent must
> > + use the same interrupt-cells format as GIC.
> > +- reg: Physical base address of the cirq registers and length of memory
> > + mapped region.
> > +- mediatek,ext-irq-start: Identifies external irq start number in different
> > + SOCs.
>
> Wouldn't this always be 32 if the GIC is the parent? If 32 is the common
> case, then use the SoC compatible to determine this value.
>

ext-irq-start is not always 32. In different Socs, this value is
different.
Thanks a lot!

> > +
> > +Example:
> > + cirq: interrupt-controller@10204000 {
> > + compatible = "mediatek,mtk-cirq";
> > + interrupt-controller;
> > + #interrupt-cells = <3>;
> > + interrupt-parent = <&sysirq>;
> > + reg = <0 0x10204000 0 0x4000>;
> > + mediatek,ext-irq-start = <32>;
> > + };
> > --
> > 1.7.9.5
> >


\
 
 \ /
  Last update: 2016-11-15 04:10    [W:0.063 / U:0.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site