lkml.org 
[lkml]   [2016]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 2/2] power: Add support for TI BQ24261 charger
Date
Hi Andy, 

> On Thu, Oct 29, 2015 at 6:34 PM, Ramakrishna Pallala
> <ramakrishna.pallala@intel.com> wrote:
> > Add new charger driver support for TI BQ24261 charger IC.
> >
> > TI BQ24261 charger driver relies on extcon notifications to get the
> > charger cable type and based on that it will set the charging parameters.
>
>
> > +/*
> > + * bq24261_charger.c - BQ24261 Charger driver
> > + *
> > + * Copyright (C) 2014 Intel Corporation
> > + * Author: Jenny TC <jenny.tc@intel.com>
>
> Authors:
>
> > + * Ramakrishna Pallala <ramakrishna.pallala@intel.com>
> > + *
>
> > +#include <linux/version.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
>
> > +#include <linux/moduleparam.h>
>
> Isn't this one is included in previous?
Fixed.

> > +#include <linux/err.h>
> > +#include <linux/init.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/slab.h>
> > +#include <linux/device.h>
> > +#include <linux/i2c.h>
> > +#include <linux/power_supply.h>
> > +#include <linux/extcon.h>
> > +#include <linux/io.h>
> > +#include <linux/sched.h>
> > +#include <linux/delay.h>
> > +#include <linux/acpi.h>
> > +#include <linux/power/bq24261_charger.h>
> > +
> > +#define DEV_NAME "bq24261-charger"
> > +
> > +#define EXCEPTION_MONITOR_DELAY (60 * HZ)
> > +#define WDT_RESET_DELAY (15 * HZ)
> > +
> > +/* BQ24261 registers */
> > +#define BQ24261_STAT_CTRL0_ADDR 0x00
> > +#define BQ24261_CTRL_ADDR 0x01
> > +#define BQ24261_BATT_VOL_CTRL_ADDR 0x02
> > +#define BQ24261_VENDOR_REV_ADDR 0x03
> > +#define BQ24261_TERM_FCC_ADDR 0x04
> > +#define BQ24261_VINDPM_STAT_ADDR 0x05
> > +#define BQ24261_ST_NTC_MON_ADDR 0x06
> > +
> > +#define BQ24261_RESET_ENABLE BIT(7)
> > +
>
> Might be a good idea to put comment line preceded each group to refer which
> register it covers.
Ok.

>
> > +#define BQ24261_FAULT_MASK GENMASK(2, 0)
>
> Either use GENMASK in each case, or put plain number.
>
Ok.

> > +#define BQ24261_VOVP 0x01
> > +#define BQ24261_LOW_SUPPLY 0x02
> > +#define BQ24261_THERMAL_SHUTDOWN 0x03
> > +#define BQ24261_BATT_TEMP_FAULT 0x04
> > +#define BQ24261_TIMER_FAULT 0x05
> > +#define BQ24261_BATT_OVP 0x06
> > +#define BQ24261_NO_BATTERY 0x07
> > +#define BQ24261_STAT_MASK (0x03 << 4)
> > +#define BQ24261_STAT_READY 0x00
>
> Would be (0x00 << 4) better to explicitly show how you apply this?
Ok.

>
> > +#define BQ24261_STAT_CHRG_PRGRSS (0x01 << 4)
> > +#define BQ24261_STAT_CHRG_DONE (0x02 << 4)
> > +#define BQ24261_STAT_FAULT (0x03 << 4)
> > +#define BQ24261_BOOST_MASK BIT(6)
> > +#define BQ24261_ENABLE_BOOST BIT(6)
>
> Similar, don't mix styles BIT vs. plain numbers. Here (0x01 << 6) looks better.
>
> Why do you need separate _MASK for one bit fields like this?
>
> > +#define BQ24261_TMR_RST_MASK (0x01 << 7)
>
> Ditto.
>
> > +#define BQ24261_TMR_RST (0x01 << 7)
> > +
> > +#define BQ24261_CE_MASK BIT(1)
>
> Ditto
>
> > +#define BQ24261_CE_DISABLE BIT(1)
> > +
> > +#define BQ24261_HiZ_MASK BIT(0)
>
> Ditto
Got it. I am moving all the BIT() & GENMASK() to (0xx << x)


> > +#define BQ24261_HiZ_ENABLE BIT(0)
> > +
> > +#define BQ24261_ICHRG_MASK GENMASK(7, 3)
> > +
> > +#define BQ24261_ITERM_MASK GENMASK(2, 0)
> > +#define BQ24261_MIN_ITERM 50 /* 50 mA */
> > +#define BQ24261_MAX_ITERM 300 /* 300 mA */
> > +
> > +#define BQ24261_VBREG_MASK GENMASK(7, 2)
> > +#define BQ24261_VBREG_MIN_CV 3500
> > +#define BQ24261_VBREG_MAX_CV 4440
> > +#define BQ24261_VBREG_CV_DIV 20
> > +#define BQ24261_VBREG_CV_BIT_POS 2
> > +
> > +#define BQ24261_INLMT_MASK GENMASK(6, 4)
> > +#define BQ24261_INLMT_100 0x00
> > +#define BQ24261_INLMT_150 (0x01 << 4)
> > +#define BQ24261_INLMT_500 (0x02 << 4)
> > +#define BQ24261_INLMT_900 (0x03 << 4)
> > +#define BQ24261_INLMT_1500 (0x04 << 4)
> > +#define BQ24261_INLMT_2000 (0x05 << 4)
> > +#define BQ24261_INLMT_2500 (0x06 << 4)
> > +
> > +#define BQ24261_TE_MASK BIT(2)
> > +#define BQ24261_TE_ENABLE BIT(2)
> > +#define BQ24261_STAT_ENABLE_MASK BIT(3)
> > +#define BQ24261_STAT_ENABLE BIT(3)
> > +
> > +#define BQ24261_VENDOR_MASK GENMASK(7, 5)
> > +#define BQ24261_PART_MASK GENMASK(4, 3)
> > +#define BQ24261_REV_MASK (0x07)
> > +#define VENDOR_BQ2426X (0x02 << 5)
> > +#define REV_BQ24261 (0x06)
> > +
> > +#define BQ24261_TS_MASK BIT(3)
> > +#define BQ24261_TS_ENABLED BIT(3)
> > +#define BQ24261_BOOST_ILIM_MASK BIT(4)
> > +#define BQ24261_BOOST_ILIM_500ma (0x0)
> > +#define BQ24261_BOOST_ILIM_1A BIT(4)
> > +#define BQ24261_VINDPM_OFF_MASK BIT(0)
> > +#define BQ24261_VINDPM_OFF_5V (0x0)
> > +#define BQ24261_VINDPM_OFF_12V BIT(0)
> > +
> > +#define BQ24261_SAFETY_TIMER_MASK GENMASK(6, 5)
> > +#define BQ24261_SAFETY_TIMER_40MIN 0x00
> > +#define BQ24261_SAFETY_TIMER_6HR (0x01 << 5)
> > +#define BQ24261_SAFETY_TIMER_9HR (0x02 << 5)
> > +#define BQ24261_SAFETY_TIMER_DISABLED (0x03 << 5)
> > +
> > +/* Settings for Voltage / DPPM Register (05) */
> > +#define BQ24261_VBATT_LEVEL1 3700000
> > +#define BQ24261_VBATT_LEVEL2 3960000
> > +#define BQ24261_VINDPM_MASK GENMASK(2, 0)
> > +#define BQ24261_VINDPM_320MV (0x01 << 2)
> > +#define BQ24261_VINDPM_160MV (0x01 << 1)
> > +#define BQ24261_VINDPM_80MV (0x01 << 0)
> > +#define BQ24261_CD_STATUS_MASK (0x01 << 3)
> > +#define BQ24261_DPM_EN_MASK (0x01 << 4)
> > +#define BQ24261_DPM_EN_FORCE (0x01 << 4)
> > +#define BQ24261_LOW_CHG_MASK (0x01 << 5)
> > +#define BQ24261_LOW_CHG_EN (0x01 << 5)
> > +#define BQ24261_LOW_CHG_DIS (~BQ24261_LOW_CHG_EN)
> > +#define BQ24261_DPM_STAT_MASK (0x01 << 6)
> > +#define BQ24261_MINSYS_STAT_MASK (0x01 << 7)
> > +
> > +#define BQ24261_MIN_CC 500 /* 500mA */
> > +#define BQ24261_MAX_CC 3000 /* 3A */
> > +#define BQ24261_DEF_CC 1300 /* 1300mA */
> > +#define BQ24261_MAX_CV 4350 /*4350mV */
> > +#define BQ24261_DEF_CV 4350 /* 4350mV */
> > +#define BQ24261_DEF_ITERM 128 /* 128mA */
> > +#define BQ24261_MIN_TEMP 0 /* 0 degC */
> > +#define BQ24261_MAX_TEMP 60 /* 60 DegC */
> > +
> > +#define ILIM_100MA 100 /* 100mA */
> > +#define ILIM_500MA 500 /* 500mA */
> > +#define ILIM_900MA 900 /* 900mA */
> > +#define ILIM_1500MA 1500 /* 1500mA */
> > +#define ILIM_2000MA 2000 /* 2000mA */
> > +#define ILIM_2500MA 2500 /* 2500mA */
> > +#define ILIM_3000MA 3000 /* 3000mA */
> > +
> > +static unsigned int dis_sysfs_write;
> > +module_param(dis_sysfs_write, int, 0644);
> > +MODULE_PARM_DESC(dis_sysfs_write,
> > + "Disable sysfs write on charge current and voltage");
> > +
> > +u16 bq24261_inlmt[][2] = {
> > + {100, BQ24261_INLMT_100},
> > + {150, BQ24261_INLMT_150},
> > + {500, BQ24261_INLMT_500},
> > + {900, BQ24261_INLMT_900},
> > + {1500, BQ24261_INLMT_1500},
> > + {2000, BQ24261_INLMT_2000},
> > + {2500, BQ24261_INLMT_2500},
> > +};
> > +
> > +
> > +enum bq24261_status {
> > + BQ24261_CHRGR_STAT_UNKNOWN,
> > + BQ24261_CHRGR_STAT_READY,
> > + BQ24261_CHRGR_STAT_CHARGING,
> > + BQ24261_CHRGR_STAT_FULL,
> > + BQ24261_CHRGR_STAT_FAULT,
> > +};
> > +
> > +enum bq2426x_model {
> > + BQ2426X = 0,
> > + BQ24260,
> > + BQ24261,
> > +};
> > +
> > +struct bq24261_charger {
> > + struct i2c_client *client;
> > + struct bq24261_platform_data *pdata;
> > + struct power_supply *psy_usb;
> > + struct delayed_work fault_mon_work;
> > + struct mutex lock;
> > + enum bq2426x_model model;
> > + struct delayed_work wdt_work;
> > + struct work_struct irq_work;
> > + struct list_head irq_queue;
> > +
> > + /* extcon charger cables */
> > + struct {
> > + struct work_struct work;
> > + struct notifier_block nb;
> > + struct extcon_specific_cable_nb sdp;
> > + struct extcon_specific_cable_nb cdp;
> > + struct extcon_specific_cable_nb dcp;
> > + struct extcon_specific_cable_nb otg;
> > + enum power_supply_type chg_type;
> > + bool boost;
> > + bool connected;
> > + } cable;
> > +
> > + bool online;
> > + bool present;
> > + int chg_health;
> > + enum bq24261_status chg_status;
> > + int cc;
> > + int cv;
> > + int inlmt;
> > + int max_cc;
> > + int max_cv;
> > + int iterm;
> > + int max_temp;
> > + int min_temp;
> > + bool is_charging_enabled;
> > +};
> > +
> > +static inline int bq24261_read_reg(struct i2c_client *client, u8 reg)
> > +{
> > + int ret;
> > +
> > + ret = i2c_smbus_read_byte_data(client, reg);
> > + if (ret < 0)
> > + dev_err(&client->dev,
> > + "error(%d) in reading reg %d\n", ret, reg);
> > + return ret;
> > +}
> > +
> > +static inline int bq24261_write_reg(struct i2c_client *client, u8
> > +reg, u8 data) {
> > + int ret;
> > +
> > + ret = i2c_smbus_write_byte_data(client, reg, data);
> > + if (ret < 0)
> > + dev_err(&client->dev,
> > + "error(%d) in writing %d to reg %d\n", ret, data, reg);
> > + return ret;
> > +}
> > +
> > +static inline int bq24261_update_reg(struct i2c_client *client, u8 reg,
> > + u8 mask, u8 val) {
> > + int ret;
> > +
> > + ret = bq24261_read_reg(client, reg);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = (ret & ~mask) | (mask & val);
> > + return bq24261_write_reg(client, reg, ret); }
> > +
> > +static void lookup_regval(u16 tbl[][2], size_t size, u16 in_val, u8
> > +*out_val) {
> > + int i;
> > +
> > + for (i = 1; i < size; ++i) {
> > + if (in_val < tbl[i][0])
> > + break;
> > + }
> > +
> > + *out_val = (u8) tbl[i - 1][1];
>
> No space after casting. Have you run checkpatch.pl?
Yes, I don’t see any warning. Anyways I am removing the space.

> > +}
> > +
> > +void bq24261_cc_to_reg(int cc, u8 *reg_val) {
> > + /*
> > + * Ichrg bits are B3-B7
> > + * Icharge = 500mA + IchrgCode * 100mA
> > + */
> > + cc = clamp_t(int, cc, BQ24261_MIN_CC, BQ24261_MAX_CC);
>
> > + cc = cc - BQ24261_MIN_CC;
>
> Why not do this in previous line? I mean change range to 0.. MAX-MIN.
Agree.

>
> > + *reg_val = (cc / 100) << 3;
>
>
> > +}
> > +
> > +void bq24261_cv_to_reg(int cv, u8 *reg_val) {
> > + int val;
> > +
> > + val = clamp_t(int, cv, BQ24261_VBREG_MIN_CV,
> BQ24261_VBREG_MAX_CV);
> > + *reg_val = (((val - BQ24261_VBREG_MIN_CV) /
> > + BQ24261_VBREG_CV_DIV)
>
> Ditto.
OK.

> > + << BQ24261_VBREG_CV_BIT_POS); }
> > +
> > +void bq24261_inlmt_to_reg(int inlmt, u8 *regval) {
> > + return lookup_regval(bq24261_inlmt, ARRAY_SIZE(bq24261_inlmt),
> > + inlmt, regval); }
> > +
> > +static inline void bq24261_iterm_to_reg(int iterm, u8 *regval) {
> > + /*
> > + * Iterm bits are B0-B2
> > + * Icharge = 50mA + ItermCode * 50mA
> > + */
> > + iterm = clamp_t(int, iterm, BQ24261_MIN_ITERM,
> BQ24261_MAX_ITERM);
> > + iterm = iterm - BQ24261_MIN_ITERM;
>
> Ditto.
OK.

> > + *regval = iterm / 50;
> > +}
> > +
> > +static inline int bq24261_init_timers(struct bq24261_charger *chip) {
> > + u8 reg_val;
> > + int ret;
> > +
> > + reg_val = BQ24261_SAFETY_TIMER_9HR;
> > +
> > + if (chip->pdata->thermal_sensing)
> > + reg_val |= BQ24261_TS_ENABLED;
> > +
> > + ret = bq24261_update_reg(chip->client, BQ24261_ST_NTC_MON_ADDR,
> > + BQ24261_TS_MASK | BQ24261_SAFETY_TIMER_MASK |
> > + BQ24261_BOOST_ILIM_MASK, reg_val);
> > +
> > + return ret;
> > +}
> > +
> > +static inline int bq24261_reset_wdt_timer(struct bq24261_charger
> > +*chip) {
> > + u8 mask = BQ24261_TMR_RST_MASK, val = BQ24261_TMR_RST;
> > +
> > + if (chip->cable.boost) {
> > + mask |= BQ24261_BOOST_MASK;
> > + val |= BQ24261_ENABLE_BOOST;
> > + }
> > +
> > + return bq24261_update_reg(chip->client, BQ24261_STAT_CTRL0_ADDR,
> > + mask, val); }
> > +
> > +static inline int bq24261_set_cc(struct bq24261_charger *chip, int
> > +cc_mA) {
> > + u8 reg_val;
> > + int ret;
> > +
> > + dev_dbg(&chip->client->dev, "%s=%d\n", __func__, cc_mA);
>
> > +
> > + if (cc_mA && (cc_mA < BQ24261_MIN_CC)) {
> > + dev_dbg(&chip->client->dev, "Set LOW_CHG bit\n");
> > + reg_val = BQ24261_LOW_CHG_EN;
> > + ret = bq24261_update_reg(chip->client,
> > + BQ24261_VINDPM_STAT_ADDR,
> > + BQ24261_LOW_CHG_MASK, reg_val);
> > + return ret;
> > + }
> > +
> > + reg_val = BQ24261_LOW_CHG_DIS;
> > + ret = bq24261_update_reg(chip->client, BQ24261_VINDPM_STAT_ADDR,
> > + BQ24261_LOW_CHG_MASK,
> > + reg_val);
> > +
> > + bq24261_cc_to_reg(cc_mA, &reg_val);
> > +
> > + return bq24261_update_reg(chip->client, BQ24261_TERM_FCC_ADDR,
> > + BQ24261_ICHRG_MASK, reg_val); }
> > +
> > +static inline int bq24261_set_cv(struct bq24261_charger *chip, int
> > +cv_mV) {
> > + u8 reg_val;
> > +
> > + dev_dbg(&chip->client->dev, "%s=%d\n", __func__, cv_mV);
> > +
> > + bq24261_cv_to_reg(cv_mV, &reg_val);
> > +
> > + return bq24261_update_reg(chip->client,
> BQ24261_BATT_VOL_CTRL_ADDR,
> > + BQ24261_VBREG_MASK, reg_val); }
> > +
> > +static inline int bq24261_set_inlmt(struct bq24261_charger *chip, int
> > +inlmt) {
> > + u8 reg_val;
> > +
> > + dev_dbg(&chip->client->dev, "%s=%d\n", __func__, inlmt);
> > +
> > + bq24261_inlmt_to_reg(inlmt, &reg_val);
> > +
> > + /*
> > + * Don't enable reset bit. Setting this
> > + * bit will reset all the registers
> > + */
> > + reg_val &= ~BQ24261_RESET_ENABLE;
> > +
> > + return bq24261_update_reg(chip->client, BQ24261_CTRL_ADDR,
> > + BQ24261_RESET_ENABLE | BQ24261_INLMT_MASK,
> > + reg_val);
> > +
> > +}
> > +
> > +static inline int bq24261_set_iterm(struct bq24261_charger *chip, int
> > +iterm) {
> > + u8 reg_val;
> > +
> > + bq24261_iterm_to_reg(iterm, &reg_val);
> > +
> > + return bq24261_update_reg(chip->client, BQ24261_TERM_FCC_ADDR,
> > + BQ24261_ITERM_MASK, reg_val); }
> > +
> > +static inline int bq24261_enable_charging(struct bq24261_charger *chip,
> > + bool
> > +enable) {
> > + int ret;
> > + u8 reg_val;
> > +
> > + if (enable) {
> > + reg_val = (~BQ24261_CE_DISABLE & BQ24261_CE_MASK);
> > + reg_val |= BQ24261_TE_ENABLE;
> > + } else {
> > + reg_val = BQ24261_CE_DISABLE;
> > + }
> > +
> > + reg_val |= BQ24261_STAT_ENABLE;
> > +
> > + /*
> > + * Don't enable reset bit. Setting this
> > + * bit will reset all the registers
> > + */
> > + reg_val &= ~BQ24261_RESET_ENABLE;
> > +
> > + ret = bq24261_update_reg(chip->client, BQ24261_CTRL_ADDR,
> > + BQ24261_STAT_ENABLE_MASK | BQ24261_RESET_ENABLE |
> > + BQ24261_CE_MASK | BQ24261_TE_MASK,
> > + reg_val);
> > + if (ret || !enable)
> > + return ret;
> > +
> > + /* Set termination current */
> > + ret = bq24261_set_iterm(chip, chip->iterm);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev, "failed to set
> > + iTerm(%d)\n", ret);
> > +
> > + /* Start WDT and Safety timers */
> > + ret = bq24261_init_timers(chip);
> > + if (ret)
> > + dev_err(&chip->client->dev, "failed to set
> > + timers(%d)\n", ret);
> > +
> > + return ret;
> > +}
> > +
> > +static inline int bq24261_enable_charger(struct bq24261_charger *chip,
> > + int
> > +enable) {
> > + u8 reg_val;
> > + int ret;
> > +
> > + reg_val = enable ? (~BQ24261_HiZ_ENABLE & BQ24261_HiZ_MASK) :
> > + BQ24261_HiZ_ENABLE;
> > +
> > + /*
> > + * Don't enable reset bit. Setting this
> > + * bit will reset all the registers/
> > + */
> > + reg_val &= ~BQ24261_RESET_ENABLE;
> > +
> > + ret = bq24261_update_reg(chip->client, BQ24261_CTRL_ADDR,
> > + BQ24261_HiZ_MASK | BQ24261_RESET_ENABLE, reg_val);
> > + if (ret)
> > + return ret;
> > +
> > + return bq24261_reset_wdt_timer(chip); }
> > +
> > +static void bq24261_handle_health(struct bq24261_charger *chip, u8
> > +stat_reg) {
> > + struct i2c_client *client = chip->client;
> > + bool fault_worker = false;
> > +
> > + switch (stat_reg & BQ24261_FAULT_MASK) {
> > + case BQ24261_VOVP:
> > + chip->chg_health = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> > + fault_worker = true;
> > + dev_err(&client->dev, "Charger Over Voltage Fault\n");
> > + break;
> > + case BQ24261_LOW_SUPPLY:
> > + chip->chg_health = POWER_SUPPLY_HEALTH_DEAD;
> > + fault_worker = true;
> > + dev_err(&client->dev, "Charger Low Supply Fault\n");
> > + break;
> > + case BQ24261_THERMAL_SHUTDOWN:
> > + chip->chg_health = POWER_SUPPLY_HEALTH_OVERHEAT;
> > + dev_err(&client->dev, "Charger Thermal Fault\n");
> > + break;
> > + case BQ24261_BATT_TEMP_FAULT:
> > + dev_err(&client->dev, "Battery Temperature Fault\n");
> > + break;
> > + case BQ24261_TIMER_FAULT:
> > + chip->chg_health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> > + dev_err(&client->dev, "Charger Timer Fault\n");
> > + break;
> > + case BQ24261_BATT_OVP:
> > + chip->chg_health = POWER_SUPPLY_HEALTH_UNSPEC_FAILURE;
> > + dev_err(&client->dev, "Battery Over Voltage Fault\n");
> > + break;
> > + case BQ24261_NO_BATTERY:
> > + dev_err(&client->dev, "No Battery Connected\n");
> > + break;
> > + default:
> > + chip->chg_health = POWER_SUPPLY_HEALTH_GOOD;
> > + }
> > +
> > + if (fault_worker)
> > + schedule_delayed_work(&chip->fault_mon_work,
> > + EXCEPTION_MONITOR_DELAY); }
> > +
> > +static void bq24261_handle_status(struct bq24261_charger *chip, u8
> > +stat_reg) {
> > + struct i2c_client *client = chip->client;
> > +
> > + switch (stat_reg & BQ24261_STAT_MASK) {
> > + case BQ24261_STAT_READY:
> > + chip->chg_status = BQ24261_CHRGR_STAT_READY;
> > + dev_info(&client->dev, "Charger Status: Ready\n");
>
> dev_info? Isn't user be bothered by them?
Agree, I will change it to dev_dbg.

>
> > + break;
> > + case BQ24261_STAT_CHRG_PRGRSS:
> > + chip->chg_status = BQ24261_CHRGR_STAT_CHARGING;
> > + dev_info(&client->dev, "Charger Status: Charge Progress\n");
> > + break;
> > + case BQ24261_STAT_CHRG_DONE:
> > + chip->chg_status = BQ24261_CHRGR_STAT_FULL;
> > + dev_info(&client->dev, "Charger Status: Charge Done\n");
> > + break;
> > + case BQ24261_STAT_FAULT:
> > + chip->chg_status = BQ24261_CHRGR_STAT_FAULT;
> > + dev_warn(&client->dev, "Charger Status: Fault\n");
> > + break;
> > + default:
> > + dev_info(&client->dev, "Invalid\n");
> > + }
> > +}
> > +
> > +static int bq24261_get_charger_health(struct bq24261_charger *chip) {
> > + if (!chip->present)
> > + return POWER_SUPPLY_HEALTH_UNKNOWN;
> > +
> > + return chip->chg_health;
> > +}
> > +
> > +static int bq24261_get_charging_status(struct bq24261_charger *chip)
> > +{
> > + int status;
> > +
> > + if (!chip->present)
> > + return POWER_SUPPLY_STATUS_DISCHARGING;
> > +
> > + switch (chip->chg_status) {
> > + case BQ24261_CHRGR_STAT_READY:
> > + status = POWER_SUPPLY_STATUS_DISCHARGING;
> > + break;
> > + case BQ24261_CHRGR_STAT_CHARGING:
> > + status = POWER_SUPPLY_STATUS_CHARGING;
> > + break;
> > + case BQ24261_CHRGR_STAT_FULL:
> > + status = POWER_SUPPLY_STATUS_FULL;
> > + break;
> > + case BQ24261_CHRGR_STAT_FAULT:
> > + status = POWER_SUPPLY_STATUS_NOT_CHARGING;
> > + break;
> > + default:
> > + status = POWER_SUPPLY_STATUS_DISCHARGING;
> > + }
> > +
> > + return status;
> > +}
> > +
> > +static int bq24261_usb_get_property(struct power_supply *psy,
> > + enum power_supply_property psp, union
> > +power_supply_propval *val) {
> > + struct bq24261_charger *chip = power_supply_get_drvdata(psy);
> > +
> > + mutex_lock(&chip->lock);
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_PRESENT:
> > + val->intval = chip->present;
> > + break;
> > + case POWER_SUPPLY_PROP_ONLINE:
> > + val->intval = chip->online;
> > + break;
> > + case POWER_SUPPLY_PROP_HEALTH:
> > + val->intval = bq24261_get_charger_health(chip);
> > + break;
> > + case POWER_SUPPLY_PROP_STATUS:
> > + val->intval = bq24261_get_charging_status(chip);
> > + break;
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
> > + val->intval = chip->pdata->max_cc * 1000;
> > + break;
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
> > + val->intval = chip->pdata->max_cv * 1000;
> > + break;
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> > + val->intval = chip->cc * 1000;
> > + break;
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
> > + val->intval = chip->cv * 1000;
> > + break;
> > + case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
> > + val->intval = chip->inlmt * 1000;
> > + break;
> > + case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT:
> > + val->intval = chip->iterm * 1000;
> > + break;
> > + case POWER_SUPPLY_PROP_TEMP_MAX:
> > + val->intval = chip->pdata->max_temp * 10;
> > + break;
> > + case POWER_SUPPLY_PROP_TEMP_MIN:
> > + val->intval = chip->pdata->min_temp * 10;
> > + break;
> > + default:
> > + mutex_unlock(&chip->lock);
> > + return -EINVAL;
> > + }
> > + mutex_unlock(&chip->lock);
> > +
> > + return 0;
> > +}
> > +
> > +static int bq24261_usb_set_property(struct power_supply *psy,
> > + enum power_supply_property psp, const union
> > +power_supply_propval *val) {
> > + struct bq24261_charger *chip = power_supply_get_drvdata(psy);
> > + int intval, ret = 0;
>
> I don't see why we need the assignment
Right, will remove the assignment.

>
> > +
> > + mutex_lock(&chip->lock);
>
> Andy you are protecting exactly what here?
Device strcut variables cc and cv from read and write access.

>
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> > + /* convert uA to mA */
> > + intval = val->intval / 1000;
> > + if (intval > chip->max_cc) {
> > + ret = -EINVAL;
> > + break;
> > + }
> > +
> > + ret = bq24261_set_cc(chip, intval);
> > + if (!ret)
> > + chip->cc = intval;
> > + break;
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
> > + /* convert uA to mV */
> > + intval = val->intval / 1000;
> > + if (intval > chip->max_cv) {
> > + ret = -EINVAL;
> > + break;
> > + }
> > +
> > + ret = bq24261_set_cv(chip, intval);
> > + if (!ret)
> > + chip->cv = intval;
> > + break;
> > + default:
> > + ret = -EINVAL;
> > + }
> > + mutex_unlock(&chip->lock);
> > +
> > + return ret;
> > +}
> > +
> > +static int bq24261_property_is_writeable(struct power_supply *psy,
> > + enum power_supply_property psp) {
> > + int ret;
>
> Redundant variable.
>
Ok. Will remove it.

> > +
> > + switch (psp) {
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
> > + case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
> > + ret = 1;
> > + break;
> > + default:
> > + ret = 0;
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static enum power_supply_property bq24261_usb_props[] = {
> > + POWER_SUPPLY_PROP_PRESENT,
> > + POWER_SUPPLY_PROP_ONLINE,
> > + POWER_SUPPLY_PROP_TYPE,
> > + POWER_SUPPLY_PROP_HEALTH,
> > + POWER_SUPPLY_PROP_STATUS,
> > + POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
> > + POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
> > + POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
> > + POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
> > + POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
> > + POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
> > + POWER_SUPPLY_PROP_TEMP_MAX,
> > + POWER_SUPPLY_PROP_TEMP_MIN,
> > +};
> > +
> > +static char *bq24261_charger_supplied_to[] = {
> > + "main-battery",
> > +};
> > +
> > +static struct power_supply_desc bq24261_charger_desc = {
> > + .name = DEV_NAME,
> > + .type = POWER_SUPPLY_TYPE_USB,
> > + .properties = bq24261_usb_props,
> > + .num_properties = ARRAY_SIZE(bq24261_usb_props),
> > + .get_property = bq24261_usb_get_property,
> > +};
> > +
> > +static void bq24261_wdt_reset_worker(struct work_struct *work) {
> > +
> > + struct bq24261_charger *chip = container_of(work,
> > + struct bq24261_charger, wdt_work.work);
> > + int ret;
> > +
> > + ret = bq24261_reset_wdt_timer(chip);
> > + if (ret)
> > + dev_err(&chip->client->dev, "WDT timer reset
> > + error(%d)\n", ret);
> > +
> > + schedule_delayed_work(&chip->wdt_work, WDT_RESET_DELAY); }
> > +
> > +static void bq24261_irq_worker(struct work_struct *work) {
> > + struct bq24261_charger *chip =
> > + container_of(work, struct bq24261_charger, irq_work);
> > + int ret;
> > +
> > + /*
> > + * Lock to ensure that interrupt register readings are done
> > + * and processed sequentially. The interrupt Fault registers
> > + * are read on clear and without sequential processing double
> > + * fault interrupts or fault recovery cannot be handlled propely
> > + */
> > +
> > + mutex_lock(&chip->lock);
> > +
> > + ret = bq24261_read_reg(chip->client, BQ24261_STAT_CTRL0_ADDR);
> > + if (ret < 0) {
> > + dev_err(&chip->client->dev,
> > + "Error (%d) in reading BQ24261_STAT_CTRL0_ADDR\n", ret);
> > + goto irq_out;
> > + }
> > +
> > + if (!chip->cable.boost) {
> > + bq24261_handle_status(chip, ret);
> > + bq24261_handle_health(chip, ret);
> > + power_supply_changed(chip->psy_usb);
> > + }
> > +
> > +irq_out:
> > + mutex_unlock(&chip->lock);
> > +}
> > +
> > +static irqreturn_t bq24261_thread_handler(int id, void *data) {
> > + struct bq24261_charger *chip = (struct bq24261_charger *)data;
> > +
> > + queue_work(system_highpri_wq, &chip->irq_work);
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static void bq24261_fault_mon_work(struct work_struct *work) {
> > + struct bq24261_charger *chip = container_of(work,
> > + struct bq24261_charger, fault_mon_work.work);
> > + int ret;
> > +
> > + if ((chip->chg_health == POWER_SUPPLY_HEALTH_OVERVOLTAGE) ||
> > + (chip->chg_health == POWER_SUPPLY_HEALTH_DEAD)) {
> > +
> > + mutex_lock(&chip->lock);
> > + ret = bq24261_read_reg(chip->client, BQ24261_STAT_CTRL0_ADDR);
> > + if (ret < 0) {
> > + dev_err(&chip->client->dev,
> > + "Status register read failed(%d)\n", ret);
> > + goto fault_mon_out;
> > + }
> > +
> > + if ((ret & BQ24261_STAT_MASK) == BQ24261_STAT_READY) {
> > + dev_info(&chip->client->dev,
> > + "Charger fault recovered\n");
> > + bq24261_handle_status(chip, ret);
> > + bq24261_handle_health(chip, ret);
> > + power_supply_changed(chip->psy_usb);
> > + }
> > +fault_mon_out:
> > + mutex_unlock(&chip->lock);
> > + }
> > +}
> > +
> > +static void bq24261_boost_control(struct bq24261_charger *chip, bool
> > +enable) {
> > + int ret;
> > +
> > + if (enable)
> > + ret = bq24261_write_reg(chip->client, BQ24261_STAT_CTRL0_ADDR,
> > + BQ24261_TMR_RST | BQ24261_ENABLE_BOOST);
> > + else
> > + ret = bq24261_write_reg(chip->client,
> > +
> > + BQ24261_STAT_CTRL0_ADDR, 0x0);
> > +
> > + if (ret < 0)
> > + dev_err(&chip->client->dev,
> > + "stat cntl0 reg access error(%d)\n", ret); }
> > +
> > +static void bq24261_extcon_event_work(struct work_struct *work) {
> > + struct bq24261_charger *chip =
> > + container_of(work, struct bq24261_charger, cable.work);
> > + int ret, current_limit = 0;
> > + bool old_connected = chip->cable.connected;
> > +
> > + /* Determine cable/charger type */
> > + if (extcon_get_cable_state(chip->cable.sdp.edev,
> > + "SLOW-CHARGER") > 0) {
> > + chip->cable.connected = true;
> > + current_limit = ILIM_500MA;
> > + chip->cable.chg_type = POWER_SUPPLY_TYPE_USB;
> > + dev_dbg(&chip->client->dev, "USB SDP charger is connected");
> > + } else if (extcon_get_cable_state(chip->cable.cdp.edev,
> > + "CHARGE-DOWNSTREAM") > 0) {
> > + chip->cable.connected = true;
> > + current_limit = ILIM_1500MA;
> > + chip->cable.chg_type = POWER_SUPPLY_TYPE_USB_CDP;
> > + dev_dbg(&chip->client->dev, "USB CDP charger is connected");
> > + } else if (extcon_get_cable_state(chip->cable.dcp.edev,
> > + "FAST-CHARGER") > 0) {
> > + chip->cable.connected = true;
> > + current_limit = ILIM_1500MA;
> > + chip->cable.chg_type = POWER_SUPPLY_TYPE_USB_DCP;
> > + dev_dbg(&chip->client->dev, "USB DCP charger is connected");
> > + } else if (extcon_get_cable_state(chip->cable.otg.edev,
> > + "USB-Host") > 0) {
> > + chip->cable.boost = true;
> > + chip->cable.connected = true;
> > + dev_dbg(&chip->client->dev, "USB-Host cable is connected");
> > + } else {
> > + if (old_connected)
> > + dev_dbg(&chip->client->dev, "USB Cable disconnected");
> > + chip->cable.connected = false;
> > + chip->cable.boost = false;
> > + chip->cable.chg_type = POWER_SUPPLY_TYPE_USB;
> > + }
> > +
> > + /* Cable status changed */
> > + if (old_connected == chip->cable.connected)
> > + return;
> > +
> > + mutex_lock(&chip->lock);
> > + if (chip->cable.connected && !chip->cable.boost) {
> > + chip->inlmt = current_limit;
> > + /* Set up charging */
> > + ret = bq24261_set_cc(chip, chip->cc);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev, "set CC failed(%d)", ret);
> > + ret = bq24261_set_cv(chip, chip->cv);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev, "set CV failed(%d)", ret);
> > + ret = bq24261_set_inlmt(chip, chip->inlmt);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev, "set ILIM failed(%d)", ret);
> > + ret = bq24261_enable_charger(chip, true);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev,
> > + "enable charger failed(%d)", ret);
> > + ret = bq24261_enable_charging(chip, true);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev,
> > + "enable charging failed(%d)",
> > + ret);
> > +
> > + chip->is_charging_enabled = true;
> > + chip->present = true;
> > + chip->online = true;
> > + schedule_delayed_work(&chip->wdt_work, 0);
> > + } else if (chip->cable.connected && chip->cable.boost) {
> > + /* Enable VBUS for Host Mode */
> > + bq24261_boost_control(chip, true);
> > + schedule_delayed_work(&chip->wdt_work, 0);
> > + } else {
> > + dev_info(&chip->client->dev, "Cable disconnect event\n");
> > + cancel_delayed_work_sync(&chip->wdt_work);
> > + cancel_delayed_work_sync(&chip->fault_mon_work);
> > + bq24261_boost_control(chip, false);
> > + ret = bq24261_enable_charging(chip, false);
> > + if (ret < 0)
> > + dev_err(&chip->client->dev,
> > + "charger disable failed(%d)",
> > + ret);
> > +
> > + chip->is_charging_enabled = false;
> > + chip->present = false;
> > + chip->online = false;
> > + chip->inlmt = 0;
> > + }
> > + bq24261_charger_desc.type = chip->cable.chg_type;
> > + mutex_unlock(&chip->lock);
> > + power_supply_changed(chip->psy_usb);
> > +}
> > +
> > +static int bq24261_handle_extcon_events(struct notifier_block *nb,
> > + unsigned long event, void *param) {
> > + struct bq24261_charger *chip =
> > + container_of(nb, struct bq24261_charger, cable.nb);
> > +
> > + dev_dbg(&chip->client->dev, "external connector event(%ld)\n",
> > + event);
> > +
> > + schedule_work(&chip->cable.work);
> > + return NOTIFY_OK;
> > +}
> > +
> > +static int bq24261_extcon_register(struct bq24261_charger *chip) {
> > + int ret;
> > +
> > + INIT_WORK(&chip->cable.work, bq24261_extcon_event_work);
> > + chip->cable.nb.notifier_call = bq24261_handle_extcon_events;
> > +
> > + ret = extcon_register_interest(&chip->cable.sdp, NULL,
> > + "SLOW-CHARGER", &chip->cable.nb);
> > + if (ret < 0) {
> > + dev_warn(&chip->client->dev,
> > + "extcon SDP registration failed(%d)\n", ret);
> > + goto sdp_reg_failed;
> > + }
> > +
> > + ret = extcon_register_interest(&chip->cable.cdp, NULL,
> > + "CHARGE-DOWNSTREAM", &chip->cable.nb);
> > + if (ret < 0) {
> > + dev_warn(&chip->client->dev,
> > + "extcon CDP registration failed(%d)\n", ret);
> > + goto cdp_reg_failed;
> > + }
> > +
> > + ret = extcon_register_interest(&chip->cable.dcp, NULL,
> > + "FAST-CHARGER", &chip->cable.nb);
> > + if (ret < 0) {
> > + dev_warn(&chip->client->dev,
> > + "extcon DCP registration failed(%d)\n", ret);
> > + goto dcp_reg_failed;
> > + }
> > +
> > + ret = extcon_register_interest(&chip->cable.otg, NULL,
> > + "USB-Host", &chip->cable.nb);
> > + if (ret < 0) {
> > + dev_warn(&chip->client->dev,
> > + "extcon USB-Host registration failed(%d)\n", ret);
> > + goto otg_reg_failed;
> > + }
> > +
> > + return 0;
> > +
> > +otg_reg_failed:
> > + extcon_unregister_interest(&chip->cable.dcp);
> > +dcp_reg_failed:
> > + extcon_unregister_interest(&chip->cable.cdp);
> > +cdp_reg_failed:
> > + extcon_unregister_interest(&chip->cable.sdp);
> > +sdp_reg_failed:
> > + return -EPROBE_DEFER;
> > +}
> > +
> > +static void bq24261_of_pdata(struct bq24261_charger *chip)
>
> Why _of_ in the name? Unified device property interface makes it independent
> on fw.
Changed the name.

>
> > +{
> > + static struct bq24261_platform_data pdata;
> > + struct device *dev = &chip->client->dev;
> > + int ret, val;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,charge-current", &val);
> > + if (ret < 0)
> > + goto of_err;
> > + pdata.def_cc = val / 1000;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,battery-regulation-voltage", &val);
> > + if (ret < 0)
> > + goto of_err;
> > + pdata.def_cv = val / 1000;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,termination-current", &val);
> > + if (ret < 0)
> > + goto of_err;
> > + pdata.iterm = val / 1000;
> > +
> > + /* get optional parameters */
> > + ret = device_property_read_u32(dev,
> > + "ti,max-charge-current", &val);
> > + if (ret < 0)
> > + pdata.max_cc = BQ24261_MAX_CC;
> > + else
> > + pdata.max_cc = val / 1000;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,max-charge-voltage", &val);
> > + if (ret < 0)
> > + pdata.max_cc = BQ24261_MAX_CV;
> > + else
> > + pdata.max_cv = val / 1000;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,min-charge-temperature", &val);
> > + if (ret < 0)
> > + pdata.min_temp = BQ24261_MIN_TEMP;
> > + else
> > + pdata.min_temp = val;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,max-charge-temperature", &val);
> > + if (ret < 0)
> > + pdata.max_temp = BQ24261_MAX_TEMP;
> > + else
> > + pdata.max_temp = val;
> > +
> > + ret = device_property_read_u32(dev,
> > + "ti,thermal-sensing", &val);
> > + if (ret < 0)
> > + pdata.thermal_sensing = 0;
> > + else
> > + pdata.thermal_sensing = val;
> > +
> > + chip->pdata = &pdata;
> > +
> > + return;
> > +of_err:
> > + dev_err(dev, "error in getting DT property(%d)\n", ret);
>
> No of_ and DT, it looks and behaves independently.
Ok. Have changed the name.

> > +}
> > +
> > +static int bq24261_get_model(struct i2c_client *client,
> > + enum bq2426x_model *model) {
> > + int ret;
> > +
> > + ret = bq24261_read_reg(client, BQ24261_VENDOR_REV_ADDR);
> > + if (ret < 0)
> > + return ret;
> > +
> > + *model = BQ24261;
> > +
> > + return 0;
> > +}
> > +
> > +static int bq24261_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id) {
> > + struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
> > + struct power_supply_config charger_cfg = {};
> > + struct bq24261_charger *chip;
> > + int ret;
> > + enum bq2426x_model model;
> > +
> > + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
> > + dev_err(&client->dev,
> > + "I2C adapter %s doesn'tsupport BYTE DATA transfer\n",
> > + adapter->name);
> > + return -EIO;
> > + }
> > +
> > + ret = bq24261_get_model(client, &model);
> > + if (ret < 0) {
> > + dev_err(&client->dev, "chip detection error (%d)\n", ret);
> > + return -ENODEV;
> > + }
> > +
> > + chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL);
> > + if (!chip)
> > + return -ENOMEM;
> > +
> > + chip->client = client;
> > + if (client->dev.platform_data)
> > + chip->pdata = client->dev.platform_data;
> > + else if (id->driver_data)
> > + chip->pdata = (struct bq24261_platform_data *)id->driver_data;
> > + else
> > + bq24261_of_pdata(chip);
> > +
> > + if (!chip->pdata) {
> > + dev_err(&client->dev, "platform data not found");
> > + return -ENODEV;
> > + }
> > +
> > + i2c_set_clientdata(client, chip);
> > + mutex_init(&chip->lock);
> > + chip->model = model;
> > +
> > + /* Initialize charger parameters */
> > + chip->cc = chip->pdata->def_cc;
> > + chip->cv = chip->pdata->def_cv;
> > + chip->iterm = chip->pdata->iterm;
> > + chip->chg_status = BQ24261_CHRGR_STAT_UNKNOWN;
> > + chip->chg_health = POWER_SUPPLY_HEALTH_UNKNOWN;
> > +
> > + charger_cfg.drv_data = chip;
> > + charger_cfg.supplied_to = bq24261_charger_supplied_to;
> > + charger_cfg.num_supplicants =
> ARRAY_SIZE(bq24261_charger_supplied_to);
> > + if (!dis_sysfs_write) {
> > + bq24261_charger_desc.set_property = bq24261_usb_set_property;
> > + bq24261_charger_desc.property_is_writeable =
> > + bq24261_property_is_writeable;
> > + }
> > + chip->psy_usb = power_supply_register(&client->dev,
> > + &bq24261_charger_desc, &charger_cfg);
> > + if (IS_ERR(chip->psy_usb)) {
> > + dev_err(&client->dev, "power supply registration failed(%d)\n",
> > + IS_ERR(chip->psy_usb));
> > + return IS_ERR(chip->psy_usb);
> > + }
> > +
> > + INIT_DELAYED_WORK(&chip->wdt_work, bq24261_wdt_reset_worker);
> > + INIT_DELAYED_WORK(&chip->fault_mon_work,
> > + bq24261_fault_mon_work);
> > +
> > + ret = bq24261_extcon_register(chip);
> > + if (ret < 0)
> > + goto extcon_reg_failed;
> > +
> > + if (chip->client->irq) {
> > + ret = devm_request_threaded_irq(&client->dev, chip->client->irq,
> > + NULL, bq24261_thread_handler,
> > + IRQF_SHARED | IRQF_NO_SUSPEND,
> > + DEV_NAME, chip);
> > + if (ret) {
> > + dev_err(&client->dev,
> > + "irq request failed (%d)\n", ret);
> > + goto irq_reg_failed;
> > + }
> > + INIT_WORK(&chip->irq_work, bq24261_irq_worker);
> > + }
> > +
> > + /* Check for charger connected boot case */
> > + schedule_work(&chip->cable.work);
> > +
> > + return 0;
> > +
> > +irq_reg_failed:
> > + extcon_unregister_interest(&chip->cable.sdp);
> > + extcon_unregister_interest(&chip->cable.cdp);
> > + extcon_unregister_interest(&chip->cable.dcp);
> > + extcon_unregister_interest(&chip->cable.otg);
> > +extcon_reg_failed:
> > + power_supply_unregister(chip->psy_usb);
> > + return ret;
> > +}
> > +
> > +static int bq24261_remove(struct i2c_client *client) {
> > + struct bq24261_charger *chip = i2c_get_clientdata(client);
> > +
> > + flush_scheduled_work();
> > + extcon_unregister_interest(&chip->cable.sdp);
> > + extcon_unregister_interest(&chip->cable.cdp);
> > + extcon_unregister_interest(&chip->cable.dcp);
> > + extcon_unregister_interest(&chip->cable.otg);
> > + power_supply_unregister(chip->psy_usb);
> > + return 0;
> > +}
> > +
> > +static const struct i2c_device_id bq24261_id[] = {
> > + {"bq24261", 0},
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(i2c, bq24261_id);
> > +
> > +static const struct acpi_device_id bq24261_acpi_match[] = {
> > + {"TBQ24261", 0},
> > + {},
> > +};
> > +MODULE_DEVICE_TABLE(acpi, bq24261_acpi_match);
> > +
> > +static const struct of_device_id bq24261_of_match[] = {
> > + { .compatible = "ti,bq24261", },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(of, bq24261_of_match);
> > +
> > +static struct i2c_driver bq24261_driver = {
> > + .driver = {
> > + .name = DEV_NAME,
> > + .acpi_match_table = ACPI_PTR(bq24261_acpi_match),
> > + .of_match_table = of_match_ptr(bq24261_of_match),
> > + },
> > + .probe = bq24261_probe,
> > + .remove = bq24261_remove,
> > + .id_table = bq24261_id,
> > +};
> > +
> > +module_i2c_driver(bq24261_driver);
> > +
> > +MODULE_AUTHOR("Jenny TC <jenny.tc@intel.com>");
> > +MODULE_AUTHOR("Ramakrishna Pallala <ramakrishna.pallala@intel.com>");
> > +MODULE_DESCRIPTION("BQ24261 Charger Driver"); MODULE_LICENSE("GPL
> > +v2");
> > diff --git a/include/linux/power/bq24261_charger.h
> > b/include/linux/power/bq24261_charger.h
> > new file mode 100644
> > index 0000000..6c7d96e
> > --- /dev/null
> > +++ b/include/linux/power/bq24261_charger.h
> > @@ -0,0 +1,26 @@
> > +/*
> > + * bq24261_charger.h: platform data structure for bq24261 driver
> > + *
> > + * Copyright (C) 2014 Intel Corporation
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License
> > + * as published by the Free Software Foundation; version 2
> > + * of the License.
> > + */
> > +
> > +#ifndef __BQ24261_CHARGER_H__
> > +#define __BQ24261_CHARGER_H__
> > +
> > +struct bq24261_platform_data {
> > + int def_cc; /* in mA */
> > + int def_cv; /* in mV */
> > + int iterm; /* in mA */
> > + int max_cc; /* in mA */
> > + int max_cv; /* in mV */
> > + int min_temp; /* in DegC */
> > + int max_temp; /* in DegC */
> > + int thermal_sensing;
> > +};
> > +
> > +#endif
> > --
> > 1.7.9.5

Thanks,
Ram
\
 
 \ /
  Last update: 2016-01-19 02:41    [W:0.151 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site