lkml.org 
[lkml]   [2015]   [Mar]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 6/8] pinctrl: cygnus: add gpio/pinconf driver
From
Date
On Wed, 2015-03-04 at 16:35 -0800, Ray Jui wrote:
> --- a/drivers/pinctrl/bcm/Kconfig
> +++ b/drivers/pinctrl/bcm/Kconfig
> @@ -20,6 +20,28 @@ config PINCTRL_BCM2835
> select PINMUX
> select PINCONF
>
> +config PINCTRL_CYGNUS_GPIO
> + bool "Broadcom Cygnus GPIO (with PINCONF) driver"

bool type.

> + depends on OF_GPIO && ARCH_BCM_CYGNUS
> + select GPIOLIB_IRQCHIP
> + select PINCONF
> + select GENERIC_PINCONF
> + default ARCH_BCM_CYGNUS
> + help
> + Say yes here to enable the Broadcom Cygnus GPIO driver.
> +
> + The Broadcom Cygnus SoC has 3 GPIO controllers including the ASIU
> + GPIO controller (ASIU), the chipCommonG GPIO controller (CCM), and
> + the always-ON GPIO controller (CRMU/AON). All 3 GPIO controllers are
> + supported by this driver.
> +
> + All 3 Cygnus GPIO controllers support basic PINCONF functions such
> + as bias pull up, pull down, and drive strength configurations, when
> + these pins are muxed to GPIO.
> +
> + Pins from the ASIU GPIO can be individually muxed to GPIO function,
> + through interaction with the Cygnus IOMUX controller.
> +
> config PINCTRL_CYGNUS_MUX
> bool "Broadcom Cygnus IOMUX driver"
> depends on (ARCH_BCM_CYGNUS || COMPILE_TEST)
> diff --git a/drivers/pinctrl/bcm/Makefile b/drivers/pinctrl/bcm/Makefile
> index bb6beb6..2b2f70e 100644
> --- a/drivers/pinctrl/bcm/Makefile
> +++ b/drivers/pinctrl/bcm/Makefile
> @@ -2,4 +2,5 @@
>
> obj-$(CONFIG_PINCTRL_BCM281XX) += pinctrl-bcm281xx.o
> obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
> +obj-$(CONFIG_PINCTRL_CYGNUS_GPIO) += pinctrl-cygnus-gpio.o

So pinctrl-cygnus-gpio. will be built-in or not built at all.

> obj-$(CONFIG_PINCTRL_CYGNUS_MUX) += pinctrl-cygnus-mux.o
> diff --git a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
> new file mode 100644
> index 0000000..4687284
> --- /dev/null
> +++ b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
> @@ -0,0 +1,884 @@

[...]

> +MODULE_AUTHOR("Ray Jui <rjui@broadcom.com>");
> +MODULE_DESCRIPTION("Broadcom Cygnus GPIO Driver");
> +MODULE_LICENSE("GPL v2");

These three macros will be preprocessed away. (There's also
MODULE_DEVICE_TABLE. I don't yet know how that is handled in a
non-modular build, sorry.)


Paul Bolle



\
 
 \ /
  Last update: 2015-03-05 09:21    [W:0.147 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site