lkml.org 
[lkml]   [2014]   [Dec]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH RFC v6 16/21] drm: panel: Add support for Himax HX8369A MIPI DSI panel
On 12/29/2014 05:09 PM, Andrzej Hajda wrote:
> On 12/29/2014 07:39 AM, Liu Ying wrote:
>> This patch adds support for Himax HX8369A MIPI DSI panel.
>>
>> Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
>> ---
>> v5->v6:
>> * Make the checkpatch.pl script be happier.
>> * Do not set the dsi channel number to be zero in probe(), because the MIPI DSI
>> bus driver would set it.
>>
>> v4->v5:
>> * Address Andrzej Hajda's comments.
>> * Get the bs-gpios property instead of the bs[3:0]-gpios properties.
>> * Implement error propagation for panel register configurations.
>> * Other minor changes to improve the code quality.
>>
>> v3->v4:
>> * Move the relevant dt-bindings to a separate patch to address Stefan
>> Wahren's comment.
>>
>> v2->v3:
>> * Sort the included header files alphabetically.
>>
>> v1->v2:
>> * Address almost all comments from Thierry Reding.
>> * Remove several DT properties as they can be implied by the compatible string.
>> * Add the HIMAX/himax prefixes to the driver's Kconfig name and driver name.
>> * Move the driver's Makefile entry place to sort the entries alphabetically.
>> * Reuse several standard DCS functions instead of inventing wheels.
>> * Move the panel resetting and power logics to the driver probe/remove stages.
>> This may simplify panel prepare/unprepare hooks. The power consumption should
>> not change a lot at DPMS since the panel enters sleep mode at that time.
>> * Add the module author.
>> * Other minor changes, such as coding style issues.
>>
>> drivers/gpu/drm/panel/Kconfig | 5 +
>> drivers/gpu/drm/panel/Makefile | 1 +
>> drivers/gpu/drm/panel/panel-himax-hx8369a.c | 614 ++++++++++++++++++++++++++++
>> 3 files changed, 620 insertions(+)
>> create mode 100644 drivers/gpu/drm/panel/panel-himax-hx8369a.c
>>
>> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
>> index 024e98e..81b0bf0 100644
>> --- a/drivers/gpu/drm/panel/Kconfig
>> +++ b/drivers/gpu/drm/panel/Kconfig
>> @@ -16,6 +16,11 @@ config DRM_PANEL_SIMPLE
>> that it can be automatically turned off when the panel goes into a
>> low power state.
>>
>> +config DRM_PANEL_HIMAX_HX8369A
>> + tristate "Himax HX8369A panel"
>> + depends on OF
>> + select DRM_MIPI_DSI
>> +
>> config DRM_PANEL_LD9040
>> tristate "LD9040 RGB/SPI panel"
>> depends on OF && SPI
>> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
>> index 4b2a043..d5dbe06 100644
>> --- a/drivers/gpu/drm/panel/Makefile
>> +++ b/drivers/gpu/drm/panel/Makefile
>> @@ -1,4 +1,5 @@
>> obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
>> +obj-$(CONFIG_DRM_PANEL_HIMAX_HX8369A) += panel-himax-hx8369a.o
>> obj-$(CONFIG_DRM_PANEL_LD9040) += panel-ld9040.o
>> obj-$(CONFIG_DRM_PANEL_S6E8AA0) += panel-s6e8aa0.o
>> obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
>> diff --git a/drivers/gpu/drm/panel/panel-himax-hx8369a.c b/drivers/gpu/drm/panel/panel-himax-hx8369a.c
>> new file mode 100644
>> index 0000000..eee36a7
>> --- /dev/null
>> +++ b/drivers/gpu/drm/panel/panel-himax-hx8369a.c
>> @@ -0,0 +1,614 @@
>> +/*
>> + * Himax HX8369A panel driver.
>> + *
>> + * Copyright (C) 2011-2014 Freescale Semiconductor, Inc.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + *
>> + * This driver is based on Samsung s6e8aa0 panel driver.
>> + */
>> +
>> +#include <drm/drmP.h>
>> +#include <drm/drm_mipi_dsi.h>
>> +#include <drm/drm_panel.h>
>> +
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/of_device.h>
>> +#include <linux/regulator/consumer.h>
>> +
>> +#include <video/mipi_display.h>
>> +#include <video/of_videomode.h>
>> +#include <video/videomode.h>
>> +
>> +#define WRDISBV 0x51
>> +#define WRCTRLD 0x53
>> +#define WRCABC 0x55
>> +#define SETPOWER 0xb1
>> +#define SETDISP 0xb2
>> +#define SETCYC 0xb4
>> +#define SETVCOM 0xb6
>> +#define SETEXTC 0xb9
>> +#define SETMIPI 0xba
>> +#define SETPANEL 0xcc
>> +#define SETGIP 0xd5
>> +#define SETGAMMA 0xe0
>> +
>> +#define HX8369A_MIN_BRIGHTNESS 0x00
>> +#define HX8369A_MAX_BRIGHTNESS 0xff
>> +
>> +enum hx8369a_mpu_interface {
>> + HX8369A_DBI_TYPE_A_8BIT,
>> + HX8369A_DBI_TYPE_A_9BIT,
>> + HX8369A_DBI_TYPE_A_16BIT,
>> + HX8369A_DBI_TYPE_A_18BIT,
>> + HX8369A_DBI_TYPE_B_8BIT,
>> + HX8369A_DBI_TYPE_B_9BIT,
>> + HX8369A_DBI_TYPE_B_16BIT,
>> + HX8369A_DBI_TYPE_B_18BIT,
>> + HX8369A_DSI_CMD_MODE,
>> + HX8369A_DBI_TYPE_B_24BIT,
>> + HX8369A_DSI_VIDEO_MODE,
>> + HX8369A_MDDI,
>> + HX8369A_DPI_DBI_TYPE_C_OPT1,
>> + HX8369A_DPI_DBI_TYPE_C_OPT2,
>> + HX8369A_DPI_DBI_TYPE_C_OPT3
>> +};
>> +
>> +enum hx8369a_resolution {
>> + HX8369A_RES_480_864,
>> + HX8369A_RES_480_854,
>> + HX8369A_RES_480_800,
>> + HX8369A_RES_480_640,
>> + HX8369A_RES_360_640,
>> + HX8369A_RES_480_720,
>> +};
>> +
>> +struct hx8369a_panel_desc {
>> + const struct drm_display_mode *mode;
>> +
>> + /* ms */
>> + unsigned int power_on_delay;
>> + unsigned int reset_delay;
>> +
>> + unsigned int dsi_lanes;
>> +};
>> +
>> +struct hx8369a {
>> + struct device *dev;
>> + struct drm_panel panel;
>> +
>> + const struct hx8369a_panel_desc *pd;
>> +
>> + struct regulator_bulk_data supplies[5];
>> + struct gpio_desc *reset_gpio;
>> + struct gpio_desc *bs_gpio[4];
>> + u8 res_sel;
>> +};
>> +
>> +static inline struct hx8369a *panel_to_hx8369a(struct drm_panel *panel)
>> +{
>> + return container_of(panel, struct hx8369a, panel);
>> +}
>> +
>> +static int hx8369a_dcs_write(struct hx8369a *ctx, const char *func,
>> + const void *data, size_t len)
>> +{
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + ssize_t ret;
>> +
>> + ret = mipi_dsi_dcs_write_buffer(dsi, data, len);
>> + if (ret < 0) {
>> + dev_err(ctx->dev, "%s failed: %d\n", func, ret);
>> + return ret;
>> + }
>> + return 0;
>
> Nitpick. You can replace 4 lines above with:
> if (ret < 0)
> dev_err(ctx->dev, "%s failed: %d\n", func, ret);
> return ret;

I'll do that.

>
>> +}
>> +
>> +#define hx8369a_dcs_write_seq(ctx, seq...) \
>> +({ \
>> + const u8 d[] = { seq }; \
>> + BUILD_BUG_ON_MSG(ARRAY_SIZE(d) > 64, \
>> + "DCS sequence too big for stack"); \
>> + hx8369a_dcs_write(ctx, __func__, d, ARRAY_SIZE(d)); \
>> +})
>> +
>> +#define hx8369a_dcs_write_seq_static(ctx, seq...) \
>> +({ \
>> + static const u8 d[] = { seq }; \
>> + hx8369a_dcs_write(ctx, __func__, d, ARRAY_SIZE(d)); \
>> +})
>> +
>> +static int hx8369a_dsi_set_display_related_register(struct hx8369a *ctx)
>> +{
>> + u8 sec_p = (ctx->res_sel << 4) | 0x03;
>> +
>> + return hx8369a_dcs_write_seq(ctx, SETDISP, 0x00, sec_p, 0x03,
>> + 0x03, 0x70, 0x00, 0xff, 0x00, 0x00, 0x00,
>> + 0x00, 0x03, 0x03, 0x00, 0x01);
>> +}
>> +
>> +static int hx8369a_dsi_set_display_waveform_cycle(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETCYC, 0x00, 0x1d,
>> + 0x5f, 0x0e, 0x06);
>> +}
>> +
>> +static int hx8369a_dsi_set_gip(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETGIP, 0x00, 0x04,
>> + 0x03, 0x00, 0x01, 0x05, 0x1c, 0x70,
>> + 0x01, 0x03, 0x00, 0x00, 0x40, 0x06,
>> + 0x51, 0x07, 0x00, 0x00, 0x41, 0x06,
>> + 0x50, 0x07, 0x07, 0x0f, 0x04);
>> +}
>> +
>> +static int hx8369a_dsi_set_power(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETPOWER, 0x01, 0x00,
>> + 0x34, 0x06, 0x00, 0x0f, 0x0f, 0x2a,
>> + 0x32, 0x3f, 0x3f, 0x07, 0x3a, 0x01,
>> + 0xe6, 0xe6, 0xe6, 0xe6, 0xe6);
>> +}
>> +
>> +static int hx8369a_dsi_set_vcom_voltage(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETVCOM, 0x56, 0x56);
>> +}
>> +
>> +static int hx8369a_dsi_set_panel(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETPANEL, 0x02);
>> +}
>> +
>> +static int hx8369a_dsi_set_gamma_curve(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETGAMMA, 0x00, 0x1d,
>> + 0x22, 0x38, 0x3d, 0x3f, 0x2e, 0x4a,
>> + 0x06, 0x0d, 0x0f, 0x13, 0x15, 0x13,
>> + 0x16, 0x10, 0x19, 0x00, 0x1d, 0x22,
>> + 0x38, 0x3d, 0x3f, 0x2e, 0x4a, 0x06,
>> + 0x0d, 0x0f, 0x13, 0x15, 0x13, 0x16,
>> + 0x10, 0x19);
>> +}
>> +
>> +static int hx8369a_dsi_set_mipi(struct hx8369a *ctx)
>> +{
>> + u8 eleventh_p = ctx->pd->dsi_lanes == 2 ? 0x11 : 0x10;
>> +
>> + return hx8369a_dcs_write_seq(ctx, SETMIPI, 0x00, 0xa0, 0xc6,
>> + 0x00, 0x0a, 0x00, 0x10, 0x30, 0x6f,
>> + 0x02, eleventh_p, 0x18, 0x40);
>> +}
>> +
>> +static int hx8369a_dsi_set_interface_pixel_fomat(struct hx8369a *ctx)
>> +{
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + u8 format;
>> + int ret;
>> +
>> + switch (dsi->format) {
>> + case MIPI_DSI_FMT_RGB888:
>> + case MIPI_DSI_FMT_RGB666:
>> + format = 0x77;
>> + break;
>> + case MIPI_DSI_FMT_RGB565:
>> + format = 0x55;
>> + break;
>> + case MIPI_DSI_FMT_RGB666_PACKED:
>> + format = 0x66;
>> + break;
>> + default:
>> + dev_err(ctx->dev, "unsupported DSI pixel format\n");
>> + return -EINVAL;
>> + }
>> +
>> + ret = mipi_dsi_dcs_set_pixel_format(dsi, format);
>> + if (ret < 0)
>> + dev_err(ctx->dev, "%s failed: %d\n", __func__, ret);
>> + return ret;
>> +}
>
> This functions could be also DSI helper, it is not specific to this panel,
> but it is just a suggestion.

Any documentation can reflect this could be a common DSI helper,
maybe the MIPI DSI spec?
I wrote this function by taking the HX8369A panel data sheet as a
reference.

>
>> +
>> +static int hx8369a_dsi_set_column_address(struct hx8369a *ctx)
>> +{
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + const struct drm_display_mode *mode = ctx->pd->mode;
>> + int ret;
>> +
>> + ret = mipi_dsi_dcs_set_column_address(dsi, 0, mode->hdisplay - 1);
>> + if (ret < 0)
>> + dev_err(ctx->dev, "%s failed: %d\n", __func__, ret);
>> + return ret;
>> +}
>> +
>> +static int hx8369a_dsi_set_page_address(struct hx8369a *ctx)
>> +{
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + const struct drm_display_mode *mode = ctx->pd->mode;
>> + int ret;
>> +
>> + ret = mipi_dsi_dcs_set_page_address(dsi, 0, mode->vdisplay - 1);
>> + if (ret < 0)
>> + dev_err(ctx->dev, "%s failed: %d\n", __func__, ret);
>> + return ret;
>> +}
>> +
>> +static int hx8369a_dsi_write_display_brightness(struct hx8369a *ctx,
>> + u8 brightness)
>> +{
>> + return hx8369a_dcs_write_seq(ctx, WRDISBV, brightness);
>> +}
>> +
>> +static int hx8369a_dsi_write_cabc(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, WRCABC, 0x01);
>> +}
>> +
>> +static int hx8369a_dsi_write_control_display(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, WRCTRLD, 0x24);
>> +}
>> +
>> +#define hx8369a_dsi_init_helper(ctx, ret, name) \
>> +({ \
>> + ret = hx8369a_dsi_##name(ctx); \
>> + if (ret < 0) \
>> + return ret; \
>> +})
>
> Yeah, another hack to get rid of redundant code :)
> Two ugly things here: ## and return from macro.
>
>> +
>> +static int hx8369a_dsi_panel_init(struct hx8369a *ctx)
>> +{
>> + int ret;
>> +
>> + hx8369a_dsi_init_helper(ctx, ret, set_display_related_register);
>> + hx8369a_dsi_init_helper(ctx, ret, set_display_waveform_cycle);
>> + hx8369a_dsi_init_helper(ctx, ret, set_gip);
>> + hx8369a_dsi_init_helper(ctx, ret, set_power);
>> + hx8369a_dsi_init_helper(ctx, ret, set_vcom_voltage);
>> + hx8369a_dsi_init_helper(ctx, ret, set_panel);
>> + hx8369a_dsi_init_helper(ctx, ret, set_gamma_curve);
>> + hx8369a_dsi_init_helper(ctx, ret, set_mipi);
>> + hx8369a_dsi_init_helper(ctx, ret, set_interface_pixel_fomat);
>> + hx8369a_dsi_init_helper(ctx, ret, set_column_address);
>> + hx8369a_dsi_init_helper(ctx, ret, set_page_address);
>> + hx8369a_dsi_init_helper(ctx, ret, write_cabc);
>> + hx8369a_dsi_init_helper(ctx, ret, write_control_display);
>
> Maybe it would be better to replace the hack above with something like:
> {
> int (*)(struct hx8369a *ctx) funcs[] = {
> hx8369a_dsi_set_display_related_register,
> hx8369a_dsi_set_display_waveform_cycle,
> ...
> };
> int ret, i;
>
> for (i = 0; i < ARRAY_SIZE(funcs); ++i) {
> ret = funcs[i](ctx);
> if (ret)
> return ret;
> }

I'll change to use this. Thanks.

>
>> +
>> + return 0;
>> +}
>> +
>> +static int hx8369a_dsi_set_extension_command(struct hx8369a *ctx)
>> +{
>> + return hx8369a_dcs_write_seq_static(ctx, SETEXTC, 0xff, 0x83, 0x69);
>> +}
>> +
>> +static int hx8369a_dsi_set_maximum_return_packet_size(struct hx8369a *ctx,
>> + u16 size)
>> +{
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + int ret;
>> +
>> + ret = mipi_dsi_set_maximum_return_packet_size(dsi, size);
>> + if (ret < 0)
>> + dev_err(ctx->dev,
>> + "error %d setting maximum return packet size to %d\n",
>> + ret, size);
>> + return ret;
>> +}
>> +
>> +static int hx8369a_dsi_set_sequence(struct hx8369a *ctx)
>> +{
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + int ret;
>> +
>> + ret = hx8369a_dsi_set_extension_command(ctx);
>> + if (ret < 0)
>> + goto out;
>> +
>> + ret = hx8369a_dsi_set_maximum_return_packet_size(ctx, 4);
>> + if (ret < 0)
>> + goto out;
>> +
>> + ret = hx8369a_dsi_panel_init(ctx);
>> + if (ret < 0)
>> + goto out;
>> +
>> + ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
>> + if (ret < 0) {
>> + dev_err(ctx->dev, "failed to exit sleep mode: %d\n", ret);
>> + goto out;
>> + }
>> +
>> + ret = mipi_dsi_dcs_set_display_on(dsi);
>> + if (ret < 0) {
>> + dev_err(ctx->dev, "failed to set display on: %d\n", ret);
>> + goto out;
>> + }
>> +
>> + /*
>> + * It's necessary to wait 120msec after sending the Sleep Out
>> + * command before Sleep In command can be sent, according to
>> + * the HX8369A data sheet.
>> + */
>> + msleep(120);
>> +out:
>> + return ret;
>> +}
>> +
>> +static int hx8369a_dsi_disable(struct drm_panel *panel)
>> +{
>> + struct hx8369a *ctx = panel_to_hx8369a(panel);
>> +
>> + return hx8369a_dsi_write_display_brightness(ctx,
>> + HX8369A_MIN_BRIGHTNESS);
>> +}
>> +
>> +static int hx8369a_dsi_unprepare(struct drm_panel *panel)
>> +{
>> + struct hx8369a *ctx = panel_to_hx8369a(panel);
>> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
>> + int ret;
>> +
>> + ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
>> + if (ret < 0) {
>> + dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret);
>> + goto out;
>> + }
>> +
>> + ret = mipi_dsi_dcs_set_display_off(dsi);
>> + if (ret < 0) {
>> + dev_err(ctx->dev, "failed to set display off: %d\n", ret);
>> + goto out;
>> + }
>> +
>> + /*
>> + * This is to allow time for the supply voltages and clock
>> + * circuits to stablize, according to the HX8369A data sheet.
>> + */
>> + msleep(5);
>> +out:
>> + return ret;
>> +}
>> +
>> +static int hx8369a_dsi_prepare(struct drm_panel *panel)
>> +{
>> + struct hx8369a *ctx = panel_to_hx8369a(panel);
>> +
>> + return hx8369a_dsi_set_sequence(ctx);
>> +}
>> +
>> +static int hx8369a_dsi_enable(struct drm_panel *panel)
>> +{
>> + struct hx8369a *ctx = panel_to_hx8369a(panel);
>> +
>> + return hx8369a_dsi_write_display_brightness(ctx,
>> + HX8369A_MAX_BRIGHTNESS);
>> +}
>> +
>> +static int hx8369a_get_modes(struct drm_panel *panel)
>> +{
>> + struct drm_connector *connector = panel->connector;
>> + struct drm_device *drm = panel->drm;
>> + struct hx8369a *ctx = panel_to_hx8369a(panel);
>> + struct drm_display_mode *mode;
>> + const struct drm_display_mode *m = ctx->pd->mode;
>> +
>> + mode = drm_mode_duplicate(drm, m);
>> + if (!mode) {
>> + dev_err(drm->dev, "failed to add mode %ux%u@%u\n",
>> + m->hdisplay, m->vdisplay, m->vrefresh);
>> + return 0;
>> + }
>> +
>> + drm_mode_set_name(mode);
>> + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
>> +
>> + connector->display_info.bpc = 8;
>> + connector->display_info.width_mm = mode->width_mm;
>> + connector->display_info.height_mm = mode->height_mm;
>> +
>> + drm_mode_probed_add(connector, mode);
>> +
>> + return 1;
>> +}
>> +
>> +static const struct drm_panel_funcs hx8369a_dsi_drm_funcs = {
>> + .disable = hx8369a_dsi_disable,
>> + .unprepare = hx8369a_dsi_unprepare,
>> + .prepare = hx8369a_dsi_prepare,
>> + .enable = hx8369a_dsi_enable,
>> + .get_modes = hx8369a_get_modes,
>> +};
>> +
>> +static int hx8369a_power_on(struct hx8369a *ctx)
>> +{
>> + int ret;
>> +
>> + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
>> + if (ret < 0)
>> + return ret;
>> +
>> + msleep(ctx->pd->power_on_delay);
>> +
>> + gpiod_set_value(ctx->reset_gpio, 1);
>> + usleep_range(50, 60);
>> + gpiod_set_value(ctx->reset_gpio, 0);
>> +
>> + msleep(ctx->pd->reset_delay);
>> +
>> + return 0;
>> +}
>> +
>> +static int hx8369a_power_off(struct hx8369a *ctx)
>> +{
>> + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies),
>> + ctx->supplies);
>> +}
>> +
>> +static void hx8369a_vm_to_res_sel(struct hx8369a *ctx)
>> +{
>> + const struct drm_display_mode *mode = ctx->pd->mode;
>> +
>> + switch (mode->hdisplay) {
>> + case 480:
>> + switch (mode->vdisplay) {
>> + case 864:
>> + ctx->res_sel = HX8369A_RES_480_864;
>> + break;
>> + case 854:
>> + ctx->res_sel = HX8369A_RES_480_854;
>> + break;
>> + case 800:
>> + ctx->res_sel = HX8369A_RES_480_800;
>> + break;
>> + case 640:
>> + ctx->res_sel = HX8369A_RES_480_640;
>> + break;
>> + case 720:
>> + ctx->res_sel = HX8369A_RES_480_720;
>> + break;
>> + default:
>> + break;
>> + }
>> + break;
>> + case 360:
>> + if (mode->vdisplay == 640)
>> + ctx->res_sel = HX8369A_RES_360_640;
>> + break;
>> + default:
>> + break;
>> + }
>> +}
>> +
>> +static const struct drm_display_mode truly_tft480800_16_e_mode = {
>> + .clock = 26400,
>> + .hdisplay = 480,
>> + .hsync_start = 480 + 8,
>> + .hsync_end = 480 + 8 + 8,
>> + .htotal = 480 + 8 + 8 + 8,
>> + .vdisplay = 800,
>> + .vsync_start = 800 + 6,
>> + .vsync_end = 800 + 6 + 6,
>> + .vtotal = 800 + 6 + 6 + 6,
>> + .vrefresh = 60,
>> + .width_mm = 45,
>> + .height_mm = 76,
>> +};
>> +
>> +static const struct hx8369a_panel_desc truly_tft480800_16_e_dsi = {
>> + .mode = &truly_tft480800_16_e_mode,
>> + .power_on_delay = 10,
>> + .reset_delay = 10,
>> + .dsi_lanes = 2,
>> +};
>> +
>> +static const struct of_device_id hx8369a_dsi_of_match[] = {
>> + {
>> + .compatible = "truly,tft480800-16-e-dsi",
>> + .data = &truly_tft480800_16_e_dsi,
>> + }, {
>> + /* sentinel */
>> + },
>> +};
>> +MODULE_DEVICE_TABLE(of, hx8369a_dsi_of_match);
>> +
>> +static int hx8369a_dsi_probe(struct mipi_dsi_device *dsi)
>> +{
>> + struct device *dev = &dsi->dev;
>> + const struct of_device_id *of_id =
>> + of_match_device(hx8369a_dsi_of_match, dev);
>> + struct hx8369a *ctx;
>> + int ret, i;
>> +
>> + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
>> + if (!ctx)
>> + return -ENOMEM;
>> +
>> + ctx->dev = dev;
>> +
>> + if (of_id) {
>> + ctx->pd = of_id->data;
>> + } else {
>> + dev_err(dev, "cannot find compatible device\n");
>> + return -ENODEV;
>> + }
>> +
>> + hx8369a_vm_to_res_sel(ctx);
>> +
>> + ctx->supplies[0].supply = "vdd1";
>> + ctx->supplies[1].supply = "vdd2";
>> + ctx->supplies[2].supply = "vdd3";
>> + ctx->supplies[3].supply = "dsi-vcc";
>> + ctx->supplies[4].supply = "vpp";
>> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
>> + ctx->supplies);
>> + if (ret < 0) {
>> + dev_info(dev, "failed to get regulators: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
>> + if (IS_ERR(ctx->reset_gpio)) {
>> + dev_info(dev, "cannot get reset-gpios %ld\n",
>> + PTR_ERR(ctx->reset_gpio));
>> + return PTR_ERR(ctx->reset_gpio);
>> + }
>> +
>> + for (i = 0; i < 4; i++) {
>> + ctx->bs_gpio[i] = devm_gpiod_get_index(dev, "bs", i,
>> + GPIOD_OUT_HIGH);
>> + if (!IS_ERR_OR_NULL(ctx->bs_gpio[i]))
>> + dev_dbg(dev, "bs%d-gpio is configured\n", i);
>
> Are you sure you want to continue probe on error during getting gpios?

There could be holes in the gpio list as mentioned in [1].
For this panel, the potential holes mean that the relevant
gpios are not controlled by the driver but only by the
hardware.

Perhaps, I need to handle the error case.
I tried to implement it in the following way.

ctx->bs_gpio[i] = devm_gpiod_get_index(dev, "bs", i,
GPIOD_OUT_HIGH);
if (!IS_ERR_OR_NULL(ctx->bs_gpio[i])) {
dev_dbg(dev, "bs%d-gpio is configured\n", i);
} else if (IS_ERR(ctx->bs_gpio[i])) {
dev_info(dev, "failed to get bs%d-gpio\n", i);
return PTR_ERR(ctx->bs_gpio[i]);
}

But, I get this in dmesg. Any idea?
[ 1.625634] panel-hx8369a-dsi 21e0000.mipi.0: failed to get bs0-gpio
[ 1.633060] panel-hx8369a-dsi: probe of 21e0000.mipi.0 failed with
error -2

[1] Documentation/devicetree/bindings/gpio/gpio.txt.

Regards,

Liu Ying

>
> After addressing above comments you can add:
>
> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
>
>
>
> Regards
> Andrzej
>
>
>> + }
>> +
>> + ret = hx8369a_power_on(ctx);
>> + if (ret < 0) {
>> + dev_err(dev, "cannot power on\n");
>> + return ret;
>> + }
>> +
>> + drm_panel_init(&ctx->panel);
>> + ctx->panel.dev = dev;
>> + ctx->panel.funcs = &hx8369a_dsi_drm_funcs;
>> +
>> + ret = drm_panel_add(&ctx->panel);
>> + if (ret < 0)
>> + return ret;
>> +
>> + mipi_dsi_set_drvdata(dsi, ctx);
>> +
>> + dsi->lanes = ctx->pd->dsi_lanes;
>> + dsi->format = MIPI_DSI_FMT_RGB888;
>> + dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
>> + MIPI_DSI_MODE_VIDEO_BURST |
>> + MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
>> + ret = mipi_dsi_attach(dsi);
>> + if (ret < 0)
>> + drm_panel_remove(&ctx->panel);
>> +
>> + return ret;
>> +}
>> +
>> +static int hx8369a_dsi_remove(struct mipi_dsi_device *dsi)
>> +{
>> + struct hx8369a *ctx = mipi_dsi_get_drvdata(dsi);
>> +
>> + mipi_dsi_detach(dsi);
>> + drm_panel_remove(&ctx->panel);
>> + return hx8369a_power_off(ctx);
>> +}
>> +
>> +static struct mipi_dsi_driver hx8369a_dsi_driver = {
>> + .probe = hx8369a_dsi_probe,
>> + .remove = hx8369a_dsi_remove,
>> + .driver = {
>> + .name = "panel-hx8369a-dsi",
>> + .of_match_table = hx8369a_dsi_of_match,
>> + },
>> +};
>> +module_mipi_dsi_driver(hx8369a_dsi_driver);
>> +
>> +MODULE_DESCRIPTION("Himax HX8369A panel driver");
>> +MODULE_AUTHOR("Liu Ying <Ying.Liu@freescale.com>");
>> +MODULE_LICENSE("GPL v2");
>


\
 
 \ /
  Last update: 2014-12-29 11:21    [W:0.102 / U:0.172 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site